Bedienungsanleitung Jablotron GBS-210 (Seite 1 von 1) (Englisch)

554870

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

GBS-210 „VIVO“ glass break detector 2/2 MGJ51009

GBS-210 “VIVO” glass break detector

The GBS-210 glass break detector detects the breaking of glass

windows. A dual technology detection method (air pressure and sound

analysis) is used. Used processing guarantees high sensitivity to the

breaking of all types of glass. The sensitivity can be adjusted to compensate

for various window sizes and mounting distances. The GBS-210

distinguishes itself with outstanding RF immunity. A built in LED indicator

allows for easy testing and it also provides an optional alarm memory feature.

Installation

Sensitivity adjustment

LED indicator

MEM/TEST jumper

The Vivo is designed for indoor applications. It should be mounted on a

flat wall. The unit must have an unobstructed view of the protected glass (in

the case of heavy curtains, mount the detector on the window frame behind

the curtains). Do not place the detector close to any apparatuses that can

generate air pressure changes, low frequency noise or vibrations.

1. Open the cover of the detector (press in the plastic tab on the

bottom with a screwdriver).

2. Remove the PCB by pressing the flexible tab.

3. Punch through the pre-formed holes for cables and screws.

4. Attach the rear housing section to the wall.

5. Return the PCB into the housing and connect wires to the

terminals.

6. Close the cover.

Note: To avoid damaging the microphone when closing the cover,

ensure that the front housing is properly aligned before snapping shut!

Terminals

+12V, GND power supply

TAMPER tamper output (normally closed)

RELAY alarm output (normally closed)

Jumpers

MEM/TEST jumper controls the red LED function in the following way:

TEST red LED confirms detector’s triggering

MEM red LED indicates an alarm memory (it can be erased by

temporarily switching off the power supply or disconnecting

the jumper).

If the jumper is removed, the red LED will remain off.

Testing and adjusting the detector

Place the MEM/TEST jumper to the TEST position (red LED will indicate

triggering).

 Strike carefully the glass with a cushioned instrument. Attention,

do not break the glass!

 The red LED will flash shortly after a strike if the air pressure

sensor sensitivity is suitably set.

 The sensitivity can be adjusted with the variable resistor.

Note: Too high sensitivity can be a source of false alarms.

 For complete testing of the detector it is recommended to use the

GBT-212 glass break simulator. The red LED will light for 2

seconds if glass breaking is detected.

GBS-210 “VIVO” working range diagram

Notes:

The memory function can be used to determine the source of an alarm in

the system. If several detectors are used in one zone, you can set the MEM/TEST

jumper into the MEM position. Then, if this detector triggers an alarm, the red LED

will remain on until the power supply is switched off or the MEM/TEST jumper is

disconnected. The detector operates as usual even while the memory of alarm is

indicated.

A glass break detector located at the entrance can trigger a false alarm

when opening the door (air pressure change combined with keys clinking on glass

or a door’s squeaking can simulate the glass break noise). Therefore it is

recommended to connect the glass break detector into the delay zone of a control

panel.

If there is any device in the protected area which can generate a loud noise

(air conditioning, heating or cooling systems etc.), ensure that this noise does not

trigger the glass break alarm. If it does, it is necessary to relocate the detector or

assure that these devices will not be on when the security system is armed.

Specification

Power supply: 12 V DC ± 25%

Power consumption (LED off): max.10 mA

Maximum consumption (LED on): max. 35 mA

Terminals size: 1 mm2

Alarm output: normally closed, max. 60V / 50 mA,

internal resistance max.16 Ohm

Tamper output: normally closed, max. 60 V / 50 mA,

internal resistance max.16 Ohm

Detection range: max. 9 m

Minimum glass dimensions: 0.6 x 0.6 m

Initialization: max. 60 s

Security level - EN 50131-1, CLC/TS 50 131-2-7-1 grade 2,

Environment - class II. – general indoor, (EN 50131-1)

Operating temperatures -10 to +40 °C

EMC EN50130-4,EN 55022

JABLOTRON ALARMS a.s. hereby declares that the GBS-210 is

in compliance with the essential requirements and other relevant

provisions of Directive 2004/108/EC. The original of the conformity

assessment can be found on the web site www.jablotron.com

Technical Support section.

Note: Although this product does not contain any harmful materials

we suggest you return the product to the dealer or directly to the

manufacturer after use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron GBS-210 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info