Bedienungsanleitung Jablotron GC-61 (Seite 3 von 4) (Englisch)

554881

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

GC-61 GSM communicator 3 / 3 MHZ51105

3. Web server remote access

3.1. Settings via the GSMLink web server

The GSMLink server allows a user to read and change the control

panel and dialler configurations. Data transfer is done by sending an

SMS or by GRPS.

The number of SMSes sent is optimised to minimize costs. GPRS

data transfer can also be used, but must be activated on the SIM card.

3.2. GSMLink Website Registration

The www.gsmlink.cz website: To register your system use the

registration code printed on the warranty certificate (the code has the

form xxxx-xxxxx-xxxx and it is unique to each system).

You can ask for the registration code by using the DINFO SMS

command. After sending the SMS from your mobile phone: (remote

access code) DINFO “0000 DINFO”, you will receive an SMS reply

with the registration code and the level of the GSM signal.

4. User features of the GSM communicator

The GC-61 can be also used as a GSM network gateway. It cannot

be used as an ARC communicator in this mode. The 10k resistor must

be removed from PHONE terminals.

4.1. Phone calls from the attached telephone set

After the GSM module is connected to the GSM network, an attached

phone can be used to make calls. If you pick up the phone, you will

hear a dial tone. Simply dial the number you want to call (as if you are

dialling from a normal fixed line phone). You can also dial the GSM

communicator’s phone number from another phone, and its attached

phone will ring as a normal land line phone would.

Note: some telephone sets are sensitive to the GSM radio signal. For

this reason you may hear a buzzing noise in the telephone receiver

when calling. If the noise is disturbing, change the location of the

phone set (try to keep it as far as possible from the GSM dialler

antenna). Usually it is possible to find a suitable location for the phone

with a minimum level of interference.

4.2. Function of the attached SMS terminal

The communicator has a telephone connector, which can be used for

connection to an MT-77 Piccolo terminal. A detailed description is in

the separate manual enclosed with the Piccolo terminal.

Setting:

• For sending SMSes to mobile phones it is necessary to set the

SMS centre 1 to “1111”.

• By sending SMSes to telephone number “001”, the control panel

can be controlled using SMS instructions

Notes:

When displaying the caller’s telephone number (CLIP), the telephone

number is shown in international format (e.g.00420212345678).

5. Additional information

5.1. Procedure for report data transfer:

If the communicator is activated to send reports it will:

• Send information to ARC1 (to the primary number, if it fails the

backup number will be used); this process is repeated twice.

• Send information to ARC2

• If communication with the ARC is unsuccessful, the communicator

will try to send it again after a pause set by sequence PG7. The

GC-61 has a memory for 128 events.

5.2. LED indicator

• If the LED is flashing, the dialler is not registered to the GSM

network

• If the LED is flashing in short bursts:

Once in 2 seconds =normal status

Twice in 2 seconds = the balance resistor has not been detected

• If the LED is on – communication with a GSM network is occurring.

5.3. ARC communication

If the GC-61 is being used for the first time or any parameters have

been changed then the first successful communication with an ARC

will result in a short ring on the connected telephone set (if there is

one).

When the GC-61 receives 10 report codes from the control panel then

the GC-61 will suspend communication with the control panel and the

received report codes will be sent to an ARC.

The command MO can be

used to read the current status of the GSM dialler. The dialler will reply

with an SMS showing the level of GSM signal, GPRS status, and

whether data transfer to ARCs is successful or not.

Example: After sending the MO instruction, the communicator will reply

with the SMS: Alarm system reports: Control panel status:

GSM:7,GPRS OK,MS1 NOT,MS2 OK

5.4. Setting SMS

When an SMS command has been processed correctly, the GC-61

sends back a confirmation SMS e.g.:

„ Settings stored: PG11 123456789“

Or in the case of error:

„ Wrong settings“

5.5. Telephone line supervision

When a 10 k resistor is attached to the PHONE terminals, the

telephone line is balanced. When the balancing resistor is connected

to the control panel, the connection between the GC-61 and the control

panel is supervised. If the telephone line is disconnected for 30 s, the

GC-61 will send a report to an ARC.

6. Specification

Power supply 12V DC

Stand-by consumption 50 mA

Maximum consumption (during communication) 1 A

Operating bands E-GSM / GPRS 900/1800MHz

Output power 2 W for GSM900, 1 W for GSM1800

AUX terminals dry contact, max. 60 V / 100 mA

Environmental classification ( –10 to 40°C) II

EMC ETSI EN 301489-1, ETSI EN 301489-7

EN 55022, EN 5030-4

Emissions ETSI EN 301419-1 and EN 301511

Caller identification (CLIP) ETSI EN 300 089 V3.1.1(2000-12)

Jablotron Ltd. hereby declares that the GC-61 is in

compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC. The original of

the conformity assessment can be found on the web site

www.jablotron.com, Technical Support section.

Note: Dispose of batteries safely depending on battery type

and local regulations. Although this product does not contain

any harmful materials we suggest you return the product to

the dealer or directly to the manufacturer after use.

Jablotron GC-61 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info