Bedienungsanleitung Jablotron GD-04 (Seite 8 von 15) (Englisch)

554882

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

GD-04 DAVID 8 MKS51202_OS1*

responded to by an SMS report about input activation (a connection to GND). Pressing the B

button is responded to by an SMS report about input deactivation (a disconnection from GND).

• For single-button controls (such as the RC-87 or RC-89), pressing the button is responded to

by an SMS report about input activation.

• Enrolled JA-8x detectors work with the following logic:

o Input activation is reported by SMS in response to detector triggering (body movement,

door opening, breaking glass, fire, tamper...)

o Input deactivation is reported by SMS in response to panic signals or to the de-triggering

of state-providing detectors (JA-8xM)

• Wireless devices can also be assigned by entering their production code using the LRN

instruction.

• An input terminal with a wireless device assigned to it can be configured (see Optional functions,

DIP parameter g) so that connection to GND disables the reception of wireless signals. This

feature allows the setting/unsetting of enrolled detectors.

11.3.3. Controlling the outputs using an RC-8x wireless button unit

Each X or Y output

can have four OASiS wireless button units assigned to it.

1. Press and hold the XY button on the GD-04R module

2. Entering enrollment mode is indicated after 5 seconds by flashing of the LED on the

GD-04R module – release the button.

3. Enroll up to 4 wireless button units to the X output (send enrollment signals to the

module). Press the XY button again to allow enrolling to the Y output. A change of

flashing rate indicates this. Wireless button units are enrolled by pressing them.

Enrollment is confirmed by a long flash of the LED on the GD-04R. Important: Enrolling

the first device erases all the previously enrolled devices. Thus all the desired

devices should be enrolled in a single enrollment session.

4. Exit enrollment mode by pressing the XY button (enrollment is automatically terminated

after the fourth device has been assigned or after 40 seconds).

5. After enrollment mode termination, the LED on the module lights for approx. 5 seconds to

indicate enrollment data storage.

6. It is possible to enroll a wireless button unit with two buttons by pressing any button(s)

(A, B or A+B). Button A changes the status of an output (switch on – switch off), button B

always switches off an output. A wireless button unit with one button (RC-87 or RC-89),

changes the status of an output (switch on – switch off).

11.3.4. Using David for heating operation and status reporting

Each input A–D can have a wireless thermostat of the TP-8x series assigned to it (see 11.3.2).

• Enroll a thermostat to any of the A, B, C or D inputs to get reports about exceeding the

maximum/minimum allowable temperature limits in your house:

o Exceeding the upper temperature limit (e.g. 60°C) is responded to by an SMS report about

input activation.

o Dropping under the lower temperature limit (e.g. 3°C) is responded to by an SMS report

about input de-activation.

• Enroll a thermostat to one of the A or B inputs to take control of the temperature in your

house. An A-assigned thermostat controls relay X, a B-assigned thermostat controls relay Y.

This way heating control is established, supplemented by the reporting described above.

Thermostats enrolled to C or D inputs only provide reporting.

• Normally, an A- or B- enrolled thermostat switches the heating (via the X or Y relay) so that

temperature comfort is maintained. However, you can put the heating in economic mode

via an SMS instruction or by connecting the A or B input to GND. The thermostat will then

only provide anti-freeze protection: the heating will be switched on when a critically low

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron GD-04 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info