Bedienungsanleitung Jablotron GD-06 (Seite 1 von 2) (Englisch)

554883

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

GD-06 ALLEGRO GSM dealer 1/2 MHG51302

GD-06 ALLEGRO GSM Dialer

The GD-06 ALLEGRO is a universal GSM dialer and

controller. It can be used for both home and industrial

automation purposes, for security applications or any remote

data transfer project. Triggering of any of the inputs will

cause the sending of a reporting SMS message to

preprogrammed phone numbers or a direct call to a

telephone number. By using specific text messages, you can

switch on or off the remote controlled outputs. In the basic

setting, the GD-06 provides 4 inputs and 3 outputs.

The device can be programmed using programming SMS

messages or via the Internet using Jablotron’s GSMLink web

page.

The Expert mode enables full programming of all inputs and

outputs, trigeering a listening-in mode, GPRS data

communication and analogue data transmission.

1. Specification

Power supply voltage 8 - 15 V DC

Current consumption 20 mA (stand-by), 500 mA

(maximum)

GSM band E-GSM/GPRS 900/1800MHz

(2 W @ GSM900, 1 W @

GSM1800)

Terminals (P1 - P6): Input mode - triggered when

connected to GND (200 ms

filter is used)

Output mode - transistor output (max. 100 mA), switches to

GND

Relay output over-switching contact (NC-C-

NO), max. 2A / 24V

Dimensions 76 x 110 x 33 mm (antenna -

125 mm)

Complies with EN 60950, EN 301489-7, ETSI

EN 301489-7, EN55022, EN

50130-4, EN 301511

Hereby, Jablotron Ltd., declares that this GD-06 complies with the

essential requirements and other relevant provisions of Directive

1999/5/EC.

Original conformity assessment can be found at the web

page www.jablotron.cz, section Technical support.

2. Installation

The GD-06 ALLEGRO is designed for indoor use only.

Check the GSM signal strength before installing the product

(e.g. with a GSM phone using a SIM card for the same

operator).

1) Insert a SIM card into a GSM phone and disable its PIN.

If you cannot disable it, set it to 1234.

2) Insert the SIM card into the GD-06.

3) Connect the power supply.

4) The LED will start flashing until the SIM card registers

into the GSM operator’s network (max. 1 minute).

5) Standby mode is then indicated by short flashes of the

LED (apr. once every 2 sec). If the LED is lit

permanently, GSM communication is in progress.

Terminals’ description:

Wire outputs of your triggering devices (e.g. sensors, alarm

systems…) to corresponding input terminals of GD-06. Wire

the appliances which you want to control remotely to the

output terminals of the GD-06.

Note: After the installation, all telephone numbers are erased

from the memory and access codes are set to MASTER and

USER.

3. Basic setting

3.1. Reset

Reset the GD-06 communicator to the factory default

settings with English communication by sending the

instruction

“MASTER RESET EN” to the dialer

3.2. Telephone numbers setting

Store the telephone numbers TEL1 to TEL8 using the

programming SMS instruction sent from a GSM phone:

MASTER TELX YYY ZZZZZZZZZZZ

Parameter Value Description

1,2,3,4,5,6,7,8 Memory position for TEL1

to TEL8

SMS

Instruction to send SMS to

this number

YYY

SMS+

Instruction to send SMS to

this number first and then

to call this number

ZZZZZZZZZ

Telephone number (max

20 digits) , “+” prefix can

be used for international

calls

Example: “MASTER TEL1 SMS 00420483559911”

You will then receive a confirmation message from the GD-

06 to your mobile phone.

Notes:

• There must be spaces between the parameters. The SMS

instruction is case insensitive.

• For telephone numbers TEL7 and TEL8, which are used

for remote control only, you can use any YYY parameter.

• To delete the telephone number, send the SMS instruction

“MASTER TELX DEL”, for example “MASTER TEL3

DEL”.

• If the confirmation message is not in English, reset the GD-

06 as described in the paragraph 3.3.

Terminal Mode

Telephone

numbers

Power

supply

GND

Terminals for connecting

8-15 V DC power supply

voltage

Inputs

Connecting or disconnecting

to GDN will trigger sending

SMS

information to all telephone

numbers TEL1 – TEL6.

Example: "P1 On" or “P2 Off"

TEL1, TEL2,

TEL3, TEL4,

TEL5, TEL6

SMS instruction sent from

TEL1-TEL8 telephones

controls

the outputs.

Example: "ON P5" or “OFF

P6"

TEL1, TEL2,

TEL3, TEL4,

TEL5, TEL6,

TEL7, TEL8

Outputs

Relay switches over

(on/off/on…)

whenever a phone call from

TEL1 or TEL2 is detected.

TEL1, TEL2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron GD-06 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron GD-06

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info