Bedienungsanleitung Jablotron H-906SA (Seite 1 von 2) (Englisch)

555051

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

WORKING MODES OF THE H-906SA

Armed (AWAY) In this mode, all connected detectors can trigger an alarm. Detectors in the Delay Zone

will only trigger an alarm after the entrance delay.

Disarmed (HOME) In this mode, the system will not react to movement of people in the house. Detectors in

the 24Hr zone can still trigger an alarm.

Alarm If alarm is triggered, the control panel will switch on the siren and other installed

optional devices (telephone dialer, outdoor siren etc.). The alarm will reset

automatically after a predetermined period. The alarm can be stopped by the key

switch or by external controller if installed.

Service this mode can be selected only by using the key. You can service the system in this

mode (set & test sensors, set control panel etc.). No alarm can be triggered while in this

mode.

HOW TO OPERATE THE SYSTEM

The system is normally controlled by the key or by an external controller (digital keypad, remote control

etc.). If an external controller is installed, the control panel should be switched to the STAND BY position in

order to be able to accept the external controller instructions.

ARMING

To arm the system, switch the key to the ARM position (or use external controller if installed). The ARM

LED will start blinking (and the siren will sound once if the chirp function is enabled). A slow blinking of the

ARM LED indicates that the exit delay is activated. During the exit delay, any sensor in the Delay zone

can be activated without triggering the alarm. After the exit delay, the ARM LED lights permanently and all

zones are armed.

Note: No animal can stay in an area covered by motion detectors.

DISARMING

To disarm the system, switch the key to the STAND BY position (or use external controller if installed).

The ARM LED will switch off (and the siren will sound twice if the chirp function is enabled). If you trigger

any detector in the Delay zone before disarming, the system will provide an entrance delay. The entrance

delay is indicated by the fast blinking of the ARM LED and sounding of the optional chime buzzer, if

installed.

Note: If the disarming is confirmed by three chirps instead of two, check the control panel's LEDs for

important system information (alarm memory).

Zone location

Zone: protected area:

Delay L1

Instant L2

Instant L3

24 hr. L4

Exit/Entry delay: Alarm duration:

If troubles, call your installer phone:

JABLOTRON

Pod Skalkou 33

466 01 Jablonec nad Nisou

Czech Republic

tel.: 420-428--346911, fax: 420-428-313183

export@jablotron.cz

Alarm Control panel H-906SA

Description

The Hestia H-906SA is a wire operated home alarm system designed for easy installation and use. The

control panel provides four protection zones (24h, delay and two instant inputs). An assortment of

detectors can be connected to the control panel to suit your needs. Refer to the Jablotron catalog for more

details on optional detectors.

The control panel can be operated with the built-in key switch, or with an external controller (digital

keypad, remote control, hidden switch etc.). The H-906SA outputs can be connected to an external siren

(SA-105,SA-107), outdoor siren (OS-300), telephone dialer (TD-101, TD110) or a wireless pager (PG 2) to

alert of an alarm. Pre-alarm and Chirp signals are also available on H-906SA outputs.

SPECIFICATIONS

power required: 15VAC/10VA (DE-20-15 adapter can be used)

backup battery required: 12V, 1.3Ah (SA-214/1.3)

stand-by consumption: 30mA

back-up power output: 12V, max. 400mA

four zones: 24h, delay an two instant, all N.C. inputs

external ARM control input: pulse N.O. input

output rely: over-switching contact, 1A at 60 V

internal siren: 118 dB/1m

external siren output: 0.3A at 12 V

backup siren output: +BS

arm output: 0.2A to GND

chime output: 0.2A to GND

Complies with the essential requirements of: 89/336/EC EMC Directive - Protection concerning

electromagnetic compatibility when is used for its intended purpose.

Original of the conformity assessment

can be found at the web page

www.jablotron.cz, section Technical support.

Note: Dispose of batteries safely depending on the type of the batteries and local regulation. Although this

product does not contain any harmful materials we suggest you to return the product to the dealer or

directly to the producer after usage.

FRONT PANEL

POWER (Green LED) continuously lit indicates that the power supply is properly functioning. A blinking

led means that the system is powered only by the

back up battery. If this LED is off, the system has no

A.C. power and the back-up battery is discharged.

ARM (Yellow LED) if this LED is off, the system is

disarmed. If it is slowly blinking, it indicates an Exit

delay. A continuously lit LED indicates that the

system is fully armed. A rapidly blinking LED

indicates an Entrance delay.

ZONE STATUS LEDs: (DELAY, INSTANT, INSTANT, 24hr.).

When in the normal operating mode, a lit LED

indicates a triggered input. A slow blinking zone

LED indicates that there is some alarm memory

information. It can be reset by rearming. A rapidly

blinking zone means an alarm condition on the

control panel.

CONTROL KEY SWITCH has three positions: SERVICE -

you can service the system in this position (set control panel, test sensors, etc.).

POWER

ARM

DELAY

INSTANT

24 hr.

ZONE

ALARM SYSTEM

HESTIA

SERVICE ARM

STAND BY

H-906S

Alarm Control panel H-906SA 2 / 4 MCV51902 Alarm Control panel H-906SA 3 / 4 MCV51902

Jablotron H-906SA Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info