Bedienungsanleitung Jablotron JA-60IR (Seite 1 von 2) (Englisch)

554911

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

JA-60IR Wireless optical barrier MEB52800

The JA-60IR wireless optical barrier

The JA-60IR optical infrared barrier is designed to protect areas

such as doors, windows, balconies etc. within a range of 5 meters.

The detector consists of two electronic units and two IR bars. The IR

bars consist of an IR transmitter (TX) and an IR receiver (RX)

respectively with four infrared beams built-in, protecting the area

between them. A JA-60N transmitter is implemented in the RX part

for wireless communication with Jablotron systems series JA-6x,

receivers UC-216, 260 etc. The electronic units can be placed

directly on the bars or they can be placed separately (e.g. inside the

house).

Specification

IR barrier specification

Working range: 0.5m to 5 m

Number of the beams: 4 (3 + 1 Sync)

Detection time: 1 / 0.5 / 0.35 or 0.2 s

(according to the number of interrupted beams)

Optical ray ±10°at λ = 900 nm

Solar immunity ≥ 30 000 Lux at ± 5°

Power supply: 2 x lithium battery 3.6 V / 19 Ah

type ER 34615H

Battery lifetime: typically 3 year (activation 2 times a day)

Security grade 2 low to medium risk (EN 50131-1)

Environment class: IV. Outdoor general –25 to +60°C (EN 50131-1)

Dimensions

Electronic box: 40 x 40 x 240 mm

IR bar: 25 x 25 x 1000 mm

JA-60N specification

Frequency: 433.92 MHz

Can be operated according to CEPT/ERC REC 70-03

Working range: up to 100 m open area

Package contents: 2 x IR bars (RX and TX), 2 x electronic units, 2 x

connecting cables, a built-in and connected JA-60N transmitter

Jablotron s.r.o. hereby declares that the JA-60IR is in

compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EEC (EMC).

The original of the conformity assessment can be found on website

www.jablotron.com

,Technical Support section.

Installation

Open the electronic units (the TX unit is identified by a red mark and

the RX unit by a white mark). Be careful not to damage the JA-60N

transmitter which is in the cover of the RX unit.

The same identification is also used in the IR bars. To open the bars

simply slide down the top cover. When putting it back be careful not

to damage the tamper inside the bar.

The upper seals at the end of the bars are made from rubber and are

only used if the electronic units are not placed directly on the bars.

The lower seals are made from plastic with holes.

1. Choose the appropriate position to place both bars just opposite

each other and within a distance of 5 meters. Drill the holes

on the bottom parts of each bar and fix them using screws (the

connector inside the bars must point up). If necessary, it is

possible to make the bars shorter (being careful not to damage

beams or cabling) and adjust the beams according to the

specific needs of the application (by loosening the fixing

screws).

2. Fix the electronic units onto the desired place. They can be

placed directly on the top part of the bars or they can be placed

separately inside the secured premises (then seal the top part

of the bar by provided rubber padding). In the case of the RX

unit (white mark) it is also necessary to take into consideration

that the radio signal from the built-in transmitter should not be

shielded (by metal objects etc.).

3. Connect the bars to the correct electronic units (according to the

red and white marks) using the provided cable.

4. Based on the distance between the bars, set the RANGE

jumpers (see Figure 3) according to the following table:

Range RX (white mark) TX (red mark)

0.5 to 1.5 m LOW LOW

1.5 to 3 m HIGH LOW

More than 3 m HIGH HIGH

This setting also influences the battery lifetime. If the HIGH

option is set, then the consumption of the detector will be

slightly higher. But on the other hand it will increase immunity to

false alarms, especially during intense daylight.

IR transmitter

unit

IR receiver

unit

Always install the batteries

with + pole to the top

(as is shown on the picture)

Tx unit

red mark

Tx bar

Red mark

Rx unit

white mark

SYNC

Leave in

OPTO posit.

Rx bar

White mark

fixation

screws

instant

delay

Figure 1

5. To enroll the barrier to a Jablotron alarm system insert its

battery into the RX unit (white mark) while the receiver (JA-

63KR, UC-260 etc) is in enrollment mode (see also the

installation manual of the receiving unit). Set the reaction of the

barrier by DIP switch number 1 on the JA-60N transmitter (see

Figure 2):

Position ON = Instant reaction

Position 1 = delay reaction

Note: DIP switch number 2 has no influence on the function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-60IR Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info