Bedienungsanleitung Jablotron JA-63A (Seite 1 von 1) (Englisch)

554890

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

JA-63A 1 MDX52101

JA-63A Wireless siren

The JA-63A siren is designed for outdoor use. It is powered from its own

AC adapter and has a built in back up battery. The siren communicates

wirelessly with the control panel (two way communication). It contains a

high powered siren and a flashing light with a colored lens. In addition to

signaling alarms, it can also provide arming and disarming chirps. The

siren makes regular auto testing and reports its condition regularly to the

system for full supervision. Built in tamper sensors trigger an alarm if there

is any attempt to tamper with the siren.

1 2

sir e n

backup battery

15VAV

adapter

input

internal

antenna

internal antenna

jumper

DIP switches

external antenna

conne ct or

Specifications

power 15V AC (adapter SELV)

back up battery 6V, 1.3Ah (included)

working frequency 433,92 MHz

working range up to 100m (open area)

siren piezo electric, 109 dB

siren timer by control panel, max. 19 min

flash light timer 1 hour

enclosure IP34D

complies with EN 50131-1, grade 2

working environment outdoor use, -25 to +60°C; CLASS IV.

can be operated according to ERC REC 70-03

Hereby, Jablotron Ltd., declares that this JA-63A is in compliance with

the essential requirements and other relevant provisions of Directive

1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.com, section Technical support.

Installation

The siren location should not be easily accessible. Do not place the

siren close to gutters where ice could cover the siren in winter.

• select location for the AC adapter (must be indoors)

• install cable from the adapter to the desired siren location, do no

plug the adapter into the wall yet

• remove the two plastic caps on the bottom side of the housing

(with knife or other flat instrument)

• unscrew the screws located under the caps

• open the cover slowly

• select optional functions with DIP switches

• attach the siren bottom part to the desired location (first install

the top screw, then hang the siren on it and mark the positions of

the lower two screws)

• route the adapter cable to the siren and then tighten the lower

screws (the right screw in the adjustable plastic bracket is a part

of the tampering detector)

• connect the cable to 15VAC terminals (arbitrary polarity)

• connect the back up battery (flat connector)

• reattach the siren cover

Enrollment of the siren to the system

Study the system installation manual to learn how to enroll wireless

items.

• enter the enrolling mode on the control panel

• plug in the AC adapter (siren will generate an enrollment signal)

• the siren will confirm enrollment with a short sound signal

If you need to enroll a siren which is already powered and it is not

possible to switch its power off easily (for example after a control panel

reset), you can enroll it the following way: enter the control panel’s

enrolling mode and then enter the 6 digit siren production code (printed

in the siren’s manual) from the control panel’s keypad. The control panel

will automatically “request” the JA-63A siren to send its enrollment

signal. The siren will send the signal only if it has no current

communication with any other control panel (This protects you from

enrolling your neighbor’s siren). Enrollment takes about five seconds

after the code is entered.

Note: if it is impossible to enroll the siren to the control panel, it can be

the result of a weak radio signal (to long of a distance, interference etc.).

In this case the siren’s optional external antenna AN-01 can be used.

Connect the optional antenna to the external antenna connector inside

the siren and disconnect the internal antenna jumper. Fix the external

antenna on the wall (see drawing in the optional antenna bag).

Optional functions

There are two DIP switches which can change the siren functions:

#1 arming and disarming chirp sounds

position 1 – the siren will not indicate arming and disarming

position ON – the siren will confirm arming with a beep and

disarming with two beeps (3 beeps after disarming indicates user

information on the control panel). The JA-63A will also indicate a

system problem if function 391 is enabled on the control panel

(indication of system problems when arming). The JA-63A siren

chirp sound settings are valid even if function 360 is programmed

in the control panel (control panel chirps disabled) or 380 is

programmed (wireless siren alarm indication disabled).

#2 visual indication of the siren (system) status

position 2– the flashing light will make a short flash every 30

seconds if the siren’s auto testing is O.K. (=siren is ready).

position ON – the flashing light will make short flashes regularly

every 10 seconds when the alarm system is armed.

Siren function

If an alarm is triggered the siren will sound until the control panel alarm

finishes. The light will flash for 1 hour or till the system is armed.

Tampering of the siren will trigger the “TAMPER A” alarm on the control

panel. If there is some technical trouble detected in the siren or lost

communication with the siren, the control panel will indicate this as “Fault

A”. Low backup battery is signalized as “Battery A”.

The alarm function of the wireless siren can be disabled in the control

panel (with programming sequence 380). Even if the alarm function is

disabled with this setting, the optional siren functions will work,

corresponding to the settings of jumpers J1 and J2. The control panel will

also continue to confirm the presence of the JA-63A siren.

The siren requires no maintenance. The back up battery is charged

automatically. The lifetime of the back up battery is about 5 years. We

recommend its replacement after this period.

Note: if you erase the outdoor siren from the control panel (in the

enrolling mode or with a factory default reset), then the control panel

will ignore signals from the siren. However the siren will react to the

control panel signals. To erase the control panel from the siren

disconnect the siren AC adapter and back up battery for more than 20

seconds.

Warning: the control panel must be in the programming or user mode

before any changes are made with the siren. Any unauthorized changes

will trigger an alarm.

The manufacturer has no liability for consequences caused by incorrect

installation or improper use of the siren.

Note: Dispose of batteries safely depending on the type of

the batteries and local regulation. Although this product does

not contain any harmful materials we suggest you to return

the product to the dealer or

directly to the producer after usage.

Internet: www.jablotron.cz

Tel.: +420 483 559 999

fax: +420 483 559 993

Po d Ska lko u 3 3

466 01 Jablonec nad Nisou

Czech Republic

Jablotron JA-63A Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info