Bedienungsanleitung Jablotron JA-63E (Seite 1 von 1) (Englisch)

554902

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

The JA-63E wired keypad 2 / 2 MKP51001

The JA-63E digital bus wired keypad

The JA-63E keypad is designed to control and program alarm systems of

Jablotron’s JA-6x series. The keypad is equipped with backlit keys, built-in LED

signalling, acoustic signalling, and a display. It conveys information about the

system status in a convenient way. The keypad communicates via the control

panel digital bus. You can connect the keypad to the control panel via an RJ

cable or via a standard communication cable connected to terminals. Multiple

JA-63E keypads can be connected to a single control panel.

Any undesirable mishandling of the keypad (like opening its housing or tea-

ring the keypad off its position) will trigger tamper signalling. In addition, the

number of attempts to enter an access code is checked not to exceed a given

limit.

Installation

Select the desired keypad location close to the building’s entrance.

1. Open the keypad’s rear housing (by pressing the two tabs on the left or

right side).

2. Route all required cables through the hole in the rear housing and install

the housing to the desired location.

3. Connect the digital bus cable either to the terminal board or to an RJ

connector.

4. Close the keypad’s housing (attach the front housing on one side and

push it on the other side).

5. Switching on the control panel power makes the keypad ready for op-

eration.

Tabs

SYSTEM 6 0

Installation notes:

Multiple JA-63E keypads in the system must be wired in parallel. Inlet

cables can be split directly in the control panel, in a converter, in the keypad or

in a junction box. RJ cable connection and connection to terminals can be

used in combination.

A connecting cable must be wired so that the corresponding positions

(terminals) are connected. When you use a self-made RJ cable, be careful to

connect identically coloured wire ends to identically marked positions (termi-

nals).

If the keypad does not function after being connected, disconnect the

inlet cable and check if the corresponding positions (terminals) in the control

panel and the keypad are connected.

Operation

The keypad can operate and program the system to the full extent as it is

described in the control panel manual.

The following table describes the meaning of symbols on the keypad LED

indicators:

Alarm

Power supply

Tamper

Set (Armed)

Fault

Battery

Wireless communication indication

Functions F1 through F0 can be used as described in the control panel ma-

nual. Besides this, there are 4 extra keys with the following functions:

Setting (Arm-

ing)

(equal to F1

entry)

Door opening

(equal to F3 entry)

Partial setting

(equal to F2

entry)

Panic (access under

duress)

(equal to F7, before

access code entry)

Remote system access

The JA-63E keypad allows you to remotely operate or program a JA-6x

system via a phone line using a JA-60U modem. Such operation requires the

system to be equipped with a telephone communicator with the remote access

feature enabled (see the security system installation manual).

Note: Remote system access via the JA-63E keypad is only possible using a

JA-60U modem of DY62012 version or higher.

Connecting remotely to the system: Connect the JA-60U modem to the

phone line. Connect the JA-63E keypad cable to the modem’s data connector.

After powering up the modem, the keypad will show a u on the display to

indicate that it is ready to establish a connection.

The initial connection is established by keying in:

xxxxxxxx F1 y F2 ttt...t F3 nnn...n F d

where:

xxxxxxxx is an 8-digit access code for system remote access

y answering machine bypass (a so-called second call) 0-

not bypassed, 1-bypassed

ttt...t call back tel. number – if call back is not requested just

enter F3 after F2

nnn...n the remote system tel. number (a pause can be specified

by keying in F0)

d dialling method: 4-tone, 5-pulse

After the d parameter is entered, the modem will establish a connection

and the keypad will display the remote system status. The keypad then beha-

ves the same way as if it had been connected directly to the system. Depen-

ding on the quality, the telephone line might be slower in its response. A JA-

63 remote connection disables the 4 big keys on the keypad’s right side. Use

keys F0 to F9 instead.

The connection is terminated by pressing key .

A re-connection (using the same modem) is established by entering F6. The

connection parameters are memorized.

If you perform a call to a control panel which has the same access code

but a different telephone number, you do not need to re-enter the whole con-

necting sequence. Instead, it is sufficient to key in nnn...n F4 – i.e. the control

panel tel. number followed by one of the F4/F5 keys (depending on the

tone/pulse dialling method).

Technical specifications

Connection with a cable to the JA-6x digital bus connector

Connecting cable 4 core cable with RJ connectors (4/4 1:1) or

ordinary telephone cable (terminals)

Length of the inlet cable max. 100 m when a paired cable is used

Power supply 10 –14 V (taken from the digital bus)

Power consumption 25mA

Enclosure IP40

Dimensions 125 x 145 x 30 mm

Complies with EN 50131-1, EN 50131-3 grade 2

Environmental class II indoor general -10 to +40°C

EMC EN 50130-4,EN 55022

Contents of the kit: JA-63E keypad, 4 m of connecting cable,

4 rawl plugs, 4 screws, 2 RJ-44 connectors.

Accessories – for keypad connection (can be ordered separately):

RJ-40 converter from RJ connector to 4 terminals

RJ-21 RJ connector splitter (2/1)

RJ-44 cable connector (4P/4C)

RJ-00 crimping tool for RJ connectors

CT-04 cable for RJ connectors

JABLOTRON ALARMS a.s hereby declares that the JA-63E is in compliance

with the essential requirements and other relevant provisions of Directive

2004/108/EC. The original of the conformity assessment can be found at

www.jablotron.com

, Technical Support section.

Note: Although this product does not

contain any harmful materials we

suggest you return the product to the

dealer or directly to the producer after

use. See www.jablotron.com for details.

Jablotron JA-63E Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info