Bedienungsanleitung Jablotron JA-63S-80 (Seite 1 von 1) (Englisch)

554808

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

The JA-63S-80 wireless optical smoke and heat detector for Oasis system

This device is designed to detect the presence of fire inside residential or commercial

buildings. It should not be installed in industrial premises. The battery-powered detector

has a built-in local warning siren combined with a transparent LED indicator. The alarm

information can also be transferred via a wireless connection to the JA-80 OASIS

system.

The JA-63S–80 detector combines an optical smoke sensor with a heat sensor. Both

sensors have their outgoing signals processed digitally, resulting in higher false alarm

immunity. The optical sensor works using a light diffusion principle and is very sensitive to

the presence of large-sized particles which are characteristic of dense smokes. By

contrast, the sensor is less sensitive to small-sized particles which are typical of cleanly

burning fires. In particular, the smoke sensor is not capable of detecting the by-products of

cleanly-burning fluids such as alcohols, for instance. This deficiency is compensated for

by the built-in heat sensor. This sensor provides a slower reaction when compared to the

smoke sensor, but is much better at reacting to fires with rapidly rising heat producing only

a little smoke.

Smoke/heat sensor participation is configurable by DIP switches.

Detection range, detector positioning

Exposing fire conditions to the smoke and heat sensors requires some level of air

circulation. It is therefore necessary to install the JA-63S–80 detectors in such a place on

the ceiling that (in the case of fire) smoke masses are forced to go in the direction of the

detector’s position. This can usually be achieved in most buildings. However, the

JA-63S–80 is not suitable for installation in outdoor spaces or interiors with an extremely

high ceiling where fire by-products would not reach the detector position.

The following table shows the detector’s working range in relation to the height of the

ceiling on which the detector is installed. The range is expressed as the radius of the

circular fire detection area for a detector installed on a ceiling directly above:

Ceiling height (m)

< 4,5

4,5÷6

6÷8

8÷11

11÷25

> 25

Smoke

detection

7,5* m 7,5* m 7,5* m 7,5* m

Not

suitable

Not applicable

Heat

detection

5* m 5* m 5* m Not suitable

Not

applicable

Not applicable

Not applicable – meant for a particular ceiling height range

Not suitable –not usually used in such cases

* – the radius of the detection area below the detector

•

Installation on a horizontal level ceiling

Due to the possible occurrence of a cold air layer right under the ceiling, the detectors

must not be imbedded into the ceiling. The distance between any point to be

protected and an imaginary vertical line from the nearest JA-63S–80 detector down to the

floor must not exceed the radius indicated in the table.

•

Installation on a sloping ceiling

If the JA-63S–80 is installed just under an apex formed by the joining of two sloping

ceilings the values indicated in the table can be increased by 1% for every degree of

slope up to a maximum of 25%. If the space to be protected is under a saw-tooth type

of roof, JA-63S–80 detectors should be installed under each apex. However, a roof with

a shallow saw-tooth form can be acceptable if the height difference between the highest

and lowest parts of the ceiling does not exceed 5% of the total ceiling height.

•

Walls, partitions, obstacles, and trussed ceilings

The JA-63S-80 must not be installed closer than 0.5 m from any wall or partition.

A narrow room with a width of less than 1.2m requires the detector(s) to be placed at a

distance of at least one third of the room’s width away. In the case of separating walls

(partitions, warehouse objects) which do not reach the ceiling, the space is considered to

be fully separated if the gap between the top of the separating wall and the ceiling

does not exceed 0.3 m A free space of at least 0.5m is required under the detector.

Irregularities in ceiling shape which do not exceed 5% of ceiling height are considered

insignificant – the ceiling can be regarded as being even and limits from the table are

applicable. However, any irregularity (including beams) exceeding 5% of the ceiling

height is considered to be a wall with the consequences stated above.

•

Ventilation and air circulation

The detectors must not be installed directly by a fresh air inlet, e.g. air conditioning

vents. In the case of air being supplied through a perforated ceiling, each detector must

be placed so that no perforation hole occurs within 0.6m of the detector.

•

Avoid installing the detector in the following locations:

• Places with poor air circulation (niches, corners, apexes of A-shaped roofs).

• Places exposed to dust, cigarette smoke or steam.

• Places with over-intense air circulation (close to ventilators, heat sources or air

conditioning outlets).

• Kitchens and other cooking places (because steam, smoke or oily fumes can reduce

detector sensitivity).

Caution: The most common reason for the detector to be accidentally

triggered is improper detector location.

See CEN/TS 54-14 standards for detailed installation guidelines

Installation

1. Open the detector by turning the rear cover to the left and remove the battery

2. Screw the rear cover onto the desired location

3. Set the required function via the jumpers – see the table below

4. Please read the receiving device (control panel) installation manual before you

connect the battery (remove the insulation tape) and set the control panel in learning

mode

5. When the battery is connected, the detector sends a signal to connect into the

system

6. After installing the detector, allow approx. 20 seconds for stabilisation. This period is

indicated by the LED being continuously lit and is followed by an auto-test.

Successful performance of the auto-test is confirmed acoustically.

TEST

5 V

ON INSTANT alarm mode 3 OFF

Smoke (EN 14064) or heat (EN

54-5)

OFF

FIRE alarm mode

4 OFF

Memory ON

Only smoke (EN 14604) (heat

indifferent)

OFF

Memory OFF

OFF

1 2 3 4

OFF

Only heat (EN 54-5) (smoke

indifferent)

Smoke and heat (both

simultaneously)

4 ON

Closing the detector is disabled if no battery has been installed!

Testing the detector is automatically performed up to 10 secs after

battery insertion. New settings are saved directly afterwards.

Fire alarm

Optical smoke sensor: Smoke entry into the detector is indicated as a pre-alarm state

by the LED flashing. If the smoke threshold density is exceeded, a siren sound is

generated, gradually increasing in volume.

Heat sensor: indication logic is equal to that of the smoke sensor.

Alarm memory: It is switched ON/OFF via DIP 2 as shown in the table. If the event

memory is armed at the time of alarm, alarm LED indication continues even if normal

conditions are restored. The indication can be stopped by pressing the button.

Silencing the siren during an alarm: During a fire alarm, the detector LED flashes 2

times briefly and the built-in siren sounds (at a higher intensity than during a test). Under

these conditions the siren can be silenced by pressing the test button for approx. 3sec.

However, if normal conditions are not restored within approx. 10 minutes (the smoke

does not clear from the room or the temperature does not drop), the siren re-activates.

Testing the detector

Testing the detector is automatically performed up to 10 secs after battery

insertion or after changing the settings on the jumpers. The functioning of the detector

can be tested by pressing and holding the test button for approx. 3 seconds. A properly

functioning detector responds with one beep and a short flash. The alarm information is

transferred to the system. A fault is indicated by 4 beeps and the LED permanently

flashing. In this case, remove the battery and re-insert it after 1 minute. If the fault

indication occurs again (the LED starts permanently flashing after about 1 minute), consult

the installer company.

The detector should be tested this way at least once in every 30 days.

Warning: Never start a fire in a building to test the detector. Instead, use smoke-

simulating aerosols for realistic testing. The information for the control panel is seen as a

FIRE zone.

Battery replacement

The detector monitors its battery voltage and if too low, a report is sent to the control

panel and a short acoustic warning signal is emitted every 45 seconds. Battery

replacement should not be delayed by more than two weeks. As mentioned above, the

detector is automatically tested after each battery insertion. Expired batteries should

not be thrown into the garbage, but disposed according to local regulations.

Specification

Voltage 1x AA 1.5 V alkaline battery

Battery lifetime typically 2 years

Communication frequency 868,5 MHz, OASiS protocol

Wireless communication range 100m (in open space)

Smoke detection optical, light dispersion

Smoke sensor sensitivity m = 0.11 - 0.13 dB/m pursuant to EN 14 604

Temperature detection class A2 pursuant to EN 54-5

Fire-alarm temperature +60 °C to +70 °C

Acoustic power of the built-in siren min. 85 dB/3m A

Operational temperature range -10 to +70 °C

Dimensions diameter 126 mm, height 65 mm

Complies with EN 14 604, A2 EN 54-5, EN 50130-4,

EN 55022, ETSI EN 300220, EN 60950-1

1293-CPD-0261

JABLOTRON ALARMS a.s. hereby declares that the JA-63S–80 is in

compliance with the essential requirements and other relevant

provisions of Directive 1989/106/EC and 1999/5/EC. The original of the

conformity assessment can be found on the web site

www.jablotron.com, Technical Support section.

Note: Dispose of batteries safely depending on battery type and local regulations.

Although this product does not contain any harmful materials we suggest you return the

product to the dealer or directly to the manufacturer after use.

The JA-63S-80 wireless optical smoke and heat detector for Oasis system 2 / 2 MKY53100

Jablotron JA-63S-80 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info