Bedienungsanleitung Jablotron JA-65X (Seite 1 von 7) (Englisch)

554895

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Digital communicator JA-65X 1/7 MFM53102

Digital communicator JA-65X – installation manual

The JA-65X digital communicator is designed for JA-63 and

JA-65 alarm control panels. If the 65X module is installed, the

control panel can communicate with a Monitoring Station, send

voice messages, SMS messages and dial a numeric Pager as

well as communicate with a remote PC. A standard analog

telephone line (type TNV 1-3) must be connected to the module for

these functions.

1 Installation of the digital telephone

communicator

• Use the provided

telephone cable to

connect the telephone

line to the IN jack on the

X module (see diagram )

• Connect a telephone, fax

or other phone operated

device to the OUT jack,

marked with a phone

symbol

• When the control panel

is in normal stand-by mode, the phone line and any

attached device will operate as normal

Note: The communicator must be plugged directly to a

telephone line socket. All other devices (telephone, facsimile

machine, modem etc.) should be connected to the

communicator output.

2 Voice & SMS messages setting

A control panel equipped with the X module can automatically

send 2 voice and 5 short text messages (or dial a Pager). The

most convenient programming of the dialer is via a connected

PC using the Comlink software. Programming can also be

performed manually from the keypad:

• Enter the programming mode (F 0 Service Code,

factory default = 6060), indicated by „P“

• Any unfinished programming sequence can be

terminated by pressing the N key.

• To exit the programming mode, press the N key („P“

will turn off). If any fault is indicated when you try to exit

the programming mode, the control panel will inform

you about the problem.

• Telephone numbers and messages can also be set up

in the User Mode when enabled (see installation

manual of the control panel).

2.1 Telephone numbers for voice message

sending sequence: 7xxx....xxFy

Store telephone numbers for voice message by entering:

7 xx... xx F y

where:

xx...xx = telephone number

y = memory number from 1 to 4

A telephone number can have a maximum of 16 digits. A

pause can be entered by F0

Example: to store tel. number 0 123456 to memory no. 2 enter:

7 0 F0 12345 F2

Note: enter a pause (F0) after the last digit of a number which is

calling a mobile phone. This way the number will be called only

once and the dialer will not check the line signals (some mobile

phone systems do not generate standard telephone line signals).

To delete a telephone number enter: 7 F0 Fy

where:

y = memory number from 1 to 4

note: entering 7 F0 F0 will erase all tel. numbers, including the

SMS settings

When activated, the dialer will disengage all other devices

hooked up to the phone line. It will then, one by one, call all

programmed numbers and play the user recorded message

which corresponds to the event. If the dialer makes a successful

connection to a programmed number, it will not call that number

again. If the number is busy, the dialer will make 3 more

attempts to call it. Empty tel. number memories are skipped. If

all memories are empty, the dialer is completely disabled. If the

dialer is also programmed to communicate with a monitoring

station, the data will first be sent to the monitoring station.

Factory default setting: all telephone numbers are deleted.

2.2 Automatic SMS sending

sequence: 7xxx....xxF5

If Jablotron’s SMS server service is provided in your country

(check with your distributor), the following setting allows the

control panel to send alarm text messages (SMS) automatically

to a desired mobile phone:

7 xx…x F9 yy....y F7 00F9 F7zz..z F5

where:

xx…x = telephone number of the SMS server (check with

your distributor if this service is provided in your

country)

F9 = separator (recognition of server’s reaction)

yy…y = mobile phone number (where the SMS should be

sent to)

F7 = event code separator

00F9 = automatic event code – control panel will insert

there a digital code representing the alarm

(depends on setting in section 2.4)

F7 = ID separator

zz..z = optional ID number which will be sent as a part of

the SMS (ending). ID distinguishes which alarm

system sent the SMS). If ID is not required, do not

enter it

F5 = storing of the sequence to memory 5 (32 digits can

be stored to memory 5 as a maximum - separators

F9 and F7 takes only 1 digit each).

How the SMS server works: when activated, the control panel

dials the SMS server. After the connection is established, it

sends telephone number of the mobile phone, to which the SMS

should be sent. Then the control panel specifies what happened

by a digital code and in the end the ID number is transferred (if

programmed). In this moment the SMS server makes

corresponding text message and this message is sent to the

GSM network.

Example: If SMS server number is 483559876, SMS should be

sent to number 606123456 and ID number of the installation is

41 enter: 7 483559876 F9 606123456 F7 00F9 F7 41 F5

Deleting of automatic SMS sending – to erase SMS sending

enter: 7 F0 F5

Note: memory 5 can also be used to dial a Pager instead of SMS

sending. To dial a Pager enter 7 xx..x F9 zzz....z F5 where xx..x

is number of the provider, zz…z is number of the pager and code

of the message (check with a local Pager provider for details).

Pause in the dialing can be entered with F0,  with F7 and  with F8.

Pager dialing can be deleted with 7 F0 F5.

Factory default setting: SMS sending (Pager dialing) is erased.

tel. line

jack

LED diode

Microphone

Rec o r d i n g

button

JA-65X

OUT

Jablotron JA-65X Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info