Bedienungsanleitung Jablotron JA-80IR (Seite 1 von 2) (Englisch)

554801

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

JA-80IR wireless optical barrier 1 /2 MKU52302

JA-80IR wireless optical barrier

The JA-80IR optical barrier is designed for the indication of a breach into

a protected area by crossing the IR line between the transmitter and the

receiver. The barrier is a product by Optex supplemented with

transmitters compatible with OASiS systems, this being both in the

transmitting and receiving part of the barrier. The device power supply is

ensured by high-capacity lithium batteries. The signal indicating that a

transmitter and receiver battery is low is transmitted to the control panel.

The barrier occupies two enrollment positions in the system. Barrier

activation is reported by the receiving part of the barrier (the position

where its radio transmitter is enrolled in the system). Both parts of the

barrier can send a tamper signal to the control panel. The transmitters

regularly perform automatic tests and report their status to the system.

Barrier installation

The following instructions should be observed when selecting a place for

barrier installation:

 Both units must be installed onto a stationary construction (e.g. a wall or a

thick post) at the same height and should face each other.

 The area between the barrier units must not be blocked by any bushes or

tall grass.

 There can be up to a 60 m distance between the units.

 The receiver unit must not be affected by direct sunlight.

 The units should be installed 0.7 – 1 m above the ground.

 If the IR beam is parallel to a wall, there must be at least a 1 m distance

between the beam and the wall.

 If multiple barriers are used, their IR beams should not interfere with each

other.

Fig. 1 Undesirable locations

Installation steps:

The transmitting unit (marked TRANSMITER) and the receiving unit (marked

RECEIVER) are of identical mechanical construction.

Cover Optical part Rear part Base

Cover screw Rear part screw

Fig 2 Barrier parts (identical for transmitter and receiver)

1. Unscrew the rear part screws and remove the unit bases.

2. Install the bases onto the selected places, either directly on a surface

(wall) – in such a case punch two holes through the base – or onto a post

43 – 48 mm in diameter using the supplied clips and clips.

When installing the base, always check whether the rubber tamper contact

pin is functional.

Supports

Punch holes

M3 x 8

Screws

M4 x 30

Screws

Clip

Fig. 3 Preparation for installation onto a post

4. Enroll the transmitters into the system – see below.

5. Perform optical adjustment and unit transmitter setting.

6. Screw the upper covers back in and test the barrier functioning.

Enrolling the barrier transmitters into the system

The transmitters for wireless communication are located in the rear part

underneath the optical section. The barrier occupies two enrollment

positions in the system. Barrier activation is reported by the receiving

part of the barrier (the position where its radio transmitter is enrolled in

the system). Both parts of the barrier can send a tamper signal to the

control panel.

Always use two SAFT LSH20 lithium batteries to power the barriers

(they are included in the package). The batteries should be inserted very

carefully to avoid damage to the transmitter wiring. When the first

battery has been installed, the transmitter sends a signal which enrolls it

to the control panel (the control panel must be in enrollment mode at

that time – see the manual). Use switch no. 2 to set the required system

reaction to movement (ON = instant or OFF = delayed). Switch no. 1

should be left in the OFF position

rear tamper

connector

1 2

Switch 1

ISTANT

DELAYED

Switch 2

PULSE*

STATUS

Vcc

TMP

INP

GND

interconnection

to a detector

LED

set PULSE

battery not

used

Fig 4 Radio transmitter (identical for transmitter and receiver)

Setting up the optical part of the barrier

The optical part of the barrier must be adjusted so that the optical parts

facing each other are physically aligned. Both units are equipped with

adjusting elements for the adjustment of direction and a view-finder for

precise adjustment. The unit opposite the one you want to adjust must be in

the centre of the aiming cross and the cross must be in the centre of the

view-finder.

viewfinder

View through

the view-finder

correct

incorrect

Fig. 5 Setting up the optical part

When the setting is complete, it is followed by adjustment of the receiver

unit:

Connect a voltmeter to the ter-

minals and select the 0-10V range.

Watch the LED on the right

Fig. 6 setting up using a multimeter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80IR Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info