Bedienungsanleitung Jablotron JA-80P (Seite 1 von 1) (Englisch)

554795

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

JA-80P wireless PIR motion detector 1 MHP51803

The JA-80P wireless PIR motion detector

The JA-80P is a component of Jablotron’s Oasis 80 alarm system. It is

designed to detect human body movement inside buildings. The detection

pattern can be modified by optional lenses. Detector immunity has two

selectable levels. The battery-powered detector communicates via OASIS

radio protocol.

Lithium 3.6 V

Installation

Installation shall only be undertaken by technicians holding a certificate issued

by an authorized distributor. The detector can be installed on a flat wall or in

the corner of a room. Avoid objects rapidly changing in temperature, such as

electrical heaters, gas appliances etc. being positioned within its detection

area. Moving objects with a temperature close to that of humans such as

curtains moving above a radiator, and pets should also be avoided. Detectors

should not face windows or spotlights or be near fast-moving air e.g. near

ventilation fans or open windows or doors. There should also be no obstacles

blocking the detector’s “view” of the protected area. Keep the detector away

from metal objects which could interfere with radio communication.

1. Open the detector cover by pressing the tab. Avoid touching the

internal PIR element or damaging the antenna.

2. Remove the PCB which is held by an internal tab.

3. Punch screw holes through the rear plastic cover. At least one screw

should penetrate the tamper-sensitive section.

4. Screw the rear cover to the wall, about 2 metres above the floor

(vertically, with the tab down).

5. Return the PCB to its original place.

6. Leave the battery disconnected and the cover open and then follow

the control panel or receiver manual. The basics of enrollment are:

a. Enter enrollment mode on the control panel by keying in “1” in

Service mode.

b. Install a battery into the detector to activate enrollment.

c. Exit enrollment mode by pressing “#”

To enroll a detector after having already connected a battery, first disconnect

the battery, and press and release the tamper sensor to discharge any

remaining charge to ready the device for enrollment. After installing a battery

into the detector, allow one minute for stabilisation. During this minute the LED

is continuously lit.

DIP switches

NORM / HIGH: selection of immunity to false alarms. The NORM position

combines very good immunity with fast sensor reactions. The HIGH position

gives increased immunity with a slower reaction time and is only used for

problematic installations.

Warning: The most frequent cause of false alarms is bad detector positioning.

DEL / INS: DEL provides entrance & exit delays for detectors installed in a

building entrance. INS allows the detector to instantly trigger alarm activation

if the control panel is armed. This DIP switch (DEL/INS) only has an effect if

the detector has a natural reaction assigned to it in the Oasis control panel.

It also has no effect when used with a UC-8x or AC-8x receiver.

Testing the detector

15 minutes after closing the detector cover, the indicator shows detector

activation. The strength and quality of detector signals can be measured by the

control panel in Service mode.

5 minutes / 1 minute sleep time

To save battery energy, the detector switches to battery-save mode 15 minutes

after its cover is closed. During battery-save mode the detector still always watches

out for movement. The first movement detected is then signalled to the control

panel instantly, and for the next 5 minutes the detector ignores any further

movement. After these 5 minutes, the detector then returns to watching out for

movement until re-triggered. The sleep time can be shortened to 1 minute by

pressing the tamper switch during battery installation. Not pressing the tamper

switch gives a sleep time of 5 minutes.

Battery replacement

The detector monitors its battery voltage and if too low, a transmission is sent to

the control panel to inform the installer or user. The detector continues to function

and shows each detected movement with a flash of its LED. Battery replacement

should not be delayed by more than two weeks. This should be done by a

qualified technician with the control panel in Service mode.

After battery replacement, the detector needs about 60 secs to stabilise during

which its LED lights continuously. After the LED has stopped indicating, test the

detector’s functioning. Expired batteries should not be thrown into the garbage,

but disposed of according to local regulations.

Removing the detector from the system

If a detector is removed, the control panel announces the removal. The

detector has to be deleted in the control panel before intentional removal.

Detection characteristics

The default lens supplied covers an angle of 120° and a distance of 12 metres.

The area is covered by three beams as shown in the following picture.

Side view Top view

The characteristics can be changed by using optional lenses:

JS-7904 Suitable for long corridors. The middle beam covers 20 meters.

JS-7906

Only employs an upper beam with a 120° angle and a 12 metre

range. Ignoring the floor eliminates the effect of the movement of

small pets.

JS-7901

Has a vertical beam forming a wall-like detection barrier which

triggers the detector if someone walks through it.

Note: After changing the lens, test that the desired area is protected. Incorrect installation of the

lens can disable detection.

Auxiliary alarm input

There is an input terminal in the detector

which, among other things, can be used to

detect open doors or windows. Open

circuiting the input has the same effect as

movement in front of the detector

The maximum allowable cable length to

connect a normally-closed sensor to the

terminal is 3 metres. Short circuit these

terminals if the input is not used.

Technical parameters

Voltage: Lithium battery type LS(T)14500 (3,6V AA)

Typical battery lifetime: approx. 3 years (5 min. sleep mode)

Communication band: 868 MHz, Oasis protocol

Communication range: approx. 300m –( open area)

Recommended installation height: 2.0 to 2.5 m above floor level

Detection angle/detection range: 120° / 12 m (with basic lens)

Operational environment according to EN 50131-1 II.indoor general

Operational temperature range -10 to +40 °C

Dimensions 110 x 60 x 55 mm

EN 50131-1,CLC/TS 50131-2-2, EN 50131-5-3 classification: grade 2

Complies with ETSI EN 300220, EN 50130-4,EN 55022, EN 60950-1

Can be operated according to ERC REC 70-03

FCC ID VL6JA80P

Jablotron Ltd. hereby declares that the JA-80P is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC and complies with

part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This

device may not cause harmful interference, and 2. This device must accept any interference

received, including interference that may cause undesired operation.

CAUTION: Changes or modifications no expressly approved by Jablotron could void the user´s

authority to operate the equipment. The original of the conformity assessment can be found at

www.jablotron.com

, Technical Support section

Note: Although this product does

not contain any harmful materials

we suggest you return the product

to the dealer or directly to the

producer after use.

Jablotron JA-80P Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info