Bedienungsanleitung Jablotron JA-80V - LAN Communicator (Seite 1 von 10) (Englisch)

631259

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

The JA-80V LAN / PSTN line communicator - 1 - MKA51202

The JA-80V LAN / PSTN line communicator

The communicator is a component of the Jablotron Oasis 80 system. It

is designed to be installed within the control panel housing. This

manual is valid for firmware version XA64005.

When connected to a PSTN telephone line and LAN (Ethernet) data

network it allows the following:

• event reporting by SMS (to up to 8 telephone numbers)

• event reporting by phone call with an acoustic warning

• event reporting to an ARC (Automatic Receiving Centre – also

known as a Central Monitoring Station) - up to 2 ARCs

• remote control and programming by phone (remotely authorizing a

phone keypad or by SMS instructions)

• the remote control of appliances in a house by dialling in from an

authorized number (free of charge with unanswered calls)

• remote control and programming via the Internet (www.GSMlink.cz

)

The communicator can also be connected only to a telephone line or

only to a LAN network. In these cases it will provide the following

functions:

 tel. line only: remote control by phone, event reporting by SMS

and by phone calls and event reporting to ARC2 (CID protocol)

 LAN only: remote access via the Internet, event reporting to

ARC1 (IP CID protocol)

1. Installation in the control panel

If you purchased the communicator module separately, it should first

be installed in the Oasis control panel as follows:

a) The control panel power must be switched off (both mains and

battery)

b) Fit the communicator inside the control panel housing using

screws and connect its digital bus RJ cable to the main board

c) Connect the PSTN telephone line cable – the telephone line

should support CLIP protocol (EN 300 089 V3.1.1) with Caller ID

recognition and SMS transfer in text format activated (contact your

phone line provider for more details).

Ethernet - LAN

cable

Phone

line

Label with

codes

Ethernet status LED

ARC data status

RC communication fault

OASi

control panel

bus

JA-80V

Fig. 1 Communicator wiring

2. Powering up the communicator for the

first time

If the communicator is installed in the control panel then:

a) Have the LAN (Ethernet) cable ready

b) Switch on the control panel power (mains and battery). The

communicator’s green LED should turn on = no events to send to

the ARC.

c) If your LAN network does not provide an automatic DHCP,

program the Ethernet network parameters manually (see 5.18).

d) connect the LAN cable (10/100 Mbit). If communication with the

network is correct the yellow LED will be constantly lit.

If it starts flashing, check the DHCP parameters, if it turns off (after

3 sec. of flashing) then the communicator is not connected to the

Ethernet at all.

e) If communication to an ARC is desired, then all ARC parameters

have to be programmed according to the ARC provider’s

specifications.

f) Key in 98101 - to set texts of the communicator to English

language.

g) Close the control panel cover

3. User functions of the communicator

The following text describes all communicator features. The installer

should show the end user how to operate the functions used in a

particular installation.

3.1. Temporarily authorizing a phone keypad to be a system

keypad

It is possible to operate the system remotely by temporarily authorizing

a phone keypad as follows:

a) dial the system’s phone number

b) after 25 seconds of ringing (programmable) the system will answer

with a short beep

c) key in a valid access code on the telephone keypad (e.g. 8080 or

1234 if factory default settings are still valid)

d) the phone keypad will behave as a system keypad and an acoustic

signal in the receiver will indicate the control panel status: 1 beep =

SET, 2 beeps = UNSET, 3 beeps = Service mode, 4 beeps = incorrect

code entry, siren sound = alarm

e) now the system can be operated from the phone keypad the same

way as from the system keypad – including the commands starting with

∗ (for example ∗81 to turn the PGX output on)

f) to exit this mode simply end the phone call (if nothing is entered

within a minute, the phone call will end automatically anyway)

Notes:

 do not enter sequences on the phone too fast, each key signal

needs a certain time to be sent

 a fixed-line phone can also be used to operate the system

remotely the same way (the phone must use tone dialling)

 Phone keypads have to be re-authorized each time the system is

called by entering the codes specified earlier, as phone keypads are

only authorized as system keypads for the duration of a call to the

system.

3.2. SMS instructions to control the system remotely

The telephone line connected to the communicator is used to receive

SMSes but has to support CLIP protocol for SMS transfer in text form

for this feature to work. The SMS transfer parameters should also be

programmed – see 5.11 and 5.12.

All incoming SMSes are checked by the communicator and if there are

any instructions to the system, they will be performed. Each instruction

message must have the following format:

code instruction

(valid code space instruction)

Valid code = any valid code in the system (e.g. 8080, 1234 etc.)

The factory-default instruction texts (editable – see 5.4)

Instruction Function Notes

SET setting (arming)

UNSET unsetting

(disarming)

setting or unsetting (the same way as

if the code used is entered on the

system keypad), If the system is

already in the desired mode, it will not

change

STATUS status

interrogation

including ARC communication (shown

as MS1 and MS2)

MEMORY last event

interrogation

The last event recorded in the control

panel memory

PGX ON turns on PGX

PGX OFF turns off PGX

PGY ON turns on PGY

PGY OFF turns off PGY

the PG output has to be programmed

for the function: on/off (by 237/247) or

2 second switching (by 238/248)

Example: by sending: “code SET” (valid code space SET) the system

will set (if it is already set it will not change its status)

Notes:

 performance of the instruction is confirmed by an SMS reply

Jablotron JA-80V - LAN Communicator Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info