Bedienungsanleitung Jablotron JA-80X (Seite 1 von 4) (Englisch)

555057

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

The JA-80X communicator 1 / 4 MKR51103

The JA-80X phone-line communicator

Installation manual

The JA-80X communicator is a component of Jablotron systems

of the JA-8x series. It is designed to be installed within the control

panel housing. Main features:

o Alarm voice-reporting.

o ARC (Alarm Receiving Centre) communication.

o Remote access via a telephone keypad.

o Backup option for the JA-80Y GSM communicator.

The JA-80X only uses the tone dialling method.

1. Installation

• The communicator can be connected to the control panel’s

digital bus via a four-cord RJ cable. Use connectors marked RS

LINE on the communicator. Both RS LINE connectors have

parallel wiring, thus they can also be used for splitting the

control panel digital bus.

• Connect the communicator to a telephone line via the cable

supplied with the package. Use a socket marked LINE on the

communicator.

• Additional telephone devices (telephone, facsimile machine,

modem etc.) can be connected using the connector marked

“TEL”.

• When the control panel is in normal stand-by mode, the phone

line and any attached device will operate as normal.

• The communicator can only be connected to analogue phone

line and must not be connected to a dual or a grouping

extension-line.

Note: The communicator must be plugged directly into a

telephone line socket. All other devices should be connected to the

communicator output marked TEL.

2. Alarm voice-reporting

Depending on the type of events, the communicator is capable

of sending 5 assigned alarm reports to up to 4 pre-programmed

phone numbers.

• With the control panel being in the unset state, enter Service

mode by keying-in *0 SC (SC=service code, 8080 by factory

default) on the system keypad.

• Key-in the requested programming sequence(s). Any sequence

currently being entered can be escaped from by pressing #.

• Completing a sequence entry is confirmed by a beep. After

completing all the requested sequences, exit Service mode by

pressing the # key.

• Depending on system configuration, telephone numbers can

also be entered in operating mode.

2.1. Programming telephone numbers for voice

reporting sequence 71 Mxxx…xx*0

To program tel. numbers used for voice reporting enter:

71Mxx... xx *0

where:

M is the phone number memory 1 to 4

xx...xx is the desired phone number (max.16 digits)

Special codes can be put into the phone number:

Code :

by pressing

# by pressing

3 s pause by pressing

Example: Entering 712 483 123 456 *0 will store the number 483

123 456 in memory 2.

To erase a number from memory M enter:

71M*0

where: M is memory 1 to 4

Voice reports are sent to pre-programmed phone numbers in the

order they are stored. A single report to a particular tel. number

starts with the number being dialled. A 6 sec waiting period

follows. After this period voice message No. 1 is played (alarm

system identification) followed by an event description message.

This is repeated 4 times after which the communicator hangs up.

Normally, voice reporting is not terminated until after all the

numbers have been reported to. However, you can stop reporting

by alarm cancellation or by pressing the # key on the phone which

is currently being reported to.

If enabled, ARC reporting is performed prior to telephone voice

reporting.

Note: Do not program emergency call numbers!

As a factory default, all phone number memories are erased.

2.2. Limited event-reporting

sequence 792x

The communicator has a special option for the 2

tel. number

such that only INTRUSION or PANIC alarms are reported to that

number (other types of alarm events like Fire, Fault or Tamper are

not reported).

During the call to the 1st tel. number the user can decide whether

the alarm report should be also forwarded to the remaining tel.

numbers or ha can terminate further voice call reporting by

pressing # on the phone keypad (e.g. in case of the false alarm).

To program the feature enter:

792x

where:

x=0 only INTRUSION or PANIC alarms are reported to

the 2

tel. number

x=1 all events reported to all numbers

The factory default setting is 7921

This setting doesn't apply to transmissions to the ARC, which are

made via voice messages.

2.3. Voice message recording

You can record voice messages via any phone using DTMF tone

dialling. First, call the communicator’s phone number. During the

dial-up period, enter 72 on the system keypad. The communicator

will answer the call which is indicated by a beep. Press a key 0 to

8 on the phone keypad according to which of the following actions

you wish to perform:

0 – Replay all messages

1 – Record message No. 1 (Alarm reports) – identify your

alarm system (your premises)

2 – Record message No. 2 (Intrusion)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80X Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info