Bedienungsanleitung Jablotron JA-80X (Seite 3 von 4) (Englisch)

555057

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

The JA-80X communicator 3 / 4 MKR51103

3.5. ARC communication test

sequence 74

To perform the test enter:

After a successful transfer the keypad will display “test ok”. An

unsuccessful transfer is indicated by displaying “test error”.

Regular reports (group No. 7) are sent 24 hours after an event

has been reported.

3.6. Using the JA-80X and the JA80Y in

combination

The JA-80X can be used in combination with a JA-80Y GSM

communicator. The communicators can either work in parallel or

the JA-80X can operate as a backup device to the JA-80Y. In this

case, any unsuccessful attempt of the JA-80Y to report events via

GSM is followed by JA-80X voice telephone reporting.

GSM report faults are indicated by reporting “No ARC report

sent” events to the control panel memory.

Use spacing posts to install the JA-80X above the JA-80Y in the

control panel.

Notes:

• This option requires the JA-80Y to be pre-programmed by

instruction 081.

• Using two communicators in combination can reduce the

internal antenna‘s working range. If this is a problem you can

use some of Jablotron’s external antennas designed for OASiS

systems.

3.7. ARC reporting mode

sequence 791x

To program reporting mode enter:

791x

where:

x = 0 no ARC reporting from the JA-80X

x = 1 the JA-80X operates as a back-up device for

ARC1 reporting

x = 2 the JA-80X operates as a back-up device for

ARC2 reporting

x = 3 the JA-80X reports unconditionally (this requires

the installation ID and at least one phone number

to be pre-programmed)

The factory default setting is 7910.

After a JA-80X back-up report (x = 1 or 2), the JA-80Y will

perform reporting as soon as GSM communication is re-

established.

3.8. Telephone line monitoring

sequence 793x

If this function is enabled, the dialler will monitor readiness of

the telephone line. If the line is not ready it indicates problem

on the keypad and to control panel’s events memory will be

written a report “External communication fault”.

To program the feature enter:

793x

where:

x = 0 monitoring disabled

x = 1 monitoring enabled

The factory default setting is 7930 (does not comply with EN

50131-1!)

3.9. Sensitivity to signals

sequence 794x

This setting allows you to set a higher sensitivity to the line signal.

This can help in cases where the quality or level of the signal is

low.

794x

where:

x-0 basic sensitivity (default)

x-1 higher sensitivity

3.10. Busy – line detection

sequence 795x

If this function is enabled, the dialler will check for the busy tone

after dialling each phone number. If the line is busy it hangs up

and continues dialling the other numbers.

The attempt is repeated in a standard way (eight / four attempts

for communication to the ARC, four attempts for voice messages

795x

where:

x-0 detection is disabled (default)

x-1 detection is enabled

4. Remote access via a telephone line

The JA-80X communicator makes it possible to operate the

system remotely via a phone line by temporarily authorizing a

phone keypad. After a call request has been received, the

communicator will wait for a pre-programmed ringing period and

then answer the call. Subsequently, message No. 8 is replayed

(Enter your access code). After then the communicator waits for

60 sec for a Service, User or MASTER code to be entered.

If an incorrect code is entered, the communicator responds with

message No. 8 and still waits for a correct code to be entered. If

an incorrect code is detected for the second time, the

communicator responds with 4 beeps and hangs up.

A correct code entry is responded to by system status indication:

1 beep – Set (Armed)

2 beeps – Unset (Disarmed)

3 beeps – Service mode

1 long beep + 3 short beeps – Alarm state

Subsequently, the communicator replays message No. 7

“Welcome to OASiS”. The system can then be operated via the

phone keypad, the same way as from the system keypad.

Instruction performance is confirmed by beeps:

1 beep – Setting (Arming)

2 beeps – Unsetting (Disarming)

3 beeps – Entering Service mode

4 beeps – Error

Phone calls are automatically terminated after 60 seconds of

inactivity.

4.1. Ringing period

sequence 77n

To program the ringing period after which the communicator will

answer a call, enter:

77n

where:

n is a number from 0 to 9 with the following

meaning:

n = 1 to 8 the communicator will answer after n

multiplied by 5 seconds of ringing

n = 9 answers after a second call - first there must

be at least one ring, then a pause (5 to

40sec.) and then just after the first ring of

the second call, the call will be answered

n = 0 the communicator will never answer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80X Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info