Bedienungsanleitung Jablotron JA-82ST (Seite 2 von 2) (Englisch)

554807

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

The JA-82ST wireless combined smoke and heat detector MZZ57300

1: The INS alarm mode jumper sets the reaction of the system. FIRE =

alarm is triggered even if the system is disarmed while INST = alarm is

triggered only in an armed system. The INS jumper only has an effect if

the detector has a natural reaction assigned to its address in the Oasis

control panel. It also has no effect when used with a UC-8x or AC-8x

receiver.

Warning: In the INS position, while the system is disarmed, it is not

protecting against fire. This setting also fully disables the optical

and acoustic indication on the detector itself.

2: MEM Alarm memory: If the event memory is ON at the time of alarm,

alarm LED indication continues even if normal conditions are restored.

The indication can be stopped by pressing the button (indication is valid

only for FIRE settings).

3 and 4: SMOKE / TEMP sensor participation

Optical smoke sensor: Smoke entry into the detector is indicated as a

pre-alarm state by the LED flashing. If the smoke threshold density is

exceeded, a siren sound is generated (indication is valid only for FIRE

settings).

Temperature sensor: indication logic is equal to that of the smoke sensor.

Whenever the detector cover is opened, a tamper signal is sent.

Fire alarm

Optical detector: When smoke penetrates into the detector, the

detector starts flashing red and sending an alarm signal.

Heat detector: When the temperature reaches the set limits, the

detector starts flashing red and sending an alarm signal.

Alarm memory: If it is enabled, alarm indication with slow flashing

continues for a further 30 minutes even when the smoke clears. The

indication can also be terminated by turning the detector anti-clockwise to

activate the tamper sensor.

Tamper alarm: When the detector cover is opened, the detector

sends a tamper signal.

Detector testing and maintenance

The functioning of the detector can be tested with a special spray

designed for smoke detector testing to simulate fire. The test should be

carried out once in 30 days. The detector’s cover should be cleaned

regularly from dust.

Warning: never test the detector with fire.

Battery replacement

The system sends a report automatically when the battery is low.

Optical indication then flashes briefly once every 30 seconds. Remember

to switch the system to Service mode before changing the batteries

(otherwise a tamper alarm will be triggered). It is always essential to

replace all three batteries. Use the same type and the same brand for all

three. When all batteries have been inserted into the detector, a test is

carried out automatically. The test checks the battery voltage and the

sensor status and the information is then sent to the control panel.

Fault indication

The detector checks its functioning. If it detects a fault, its Optical

indication starts flashing rapidly for 1 minute and then it flashes briefly

three times every 30 seconds. In such a case, take out the battery for 1

minute and then insert it again. If the LED indicator starts flashing again

after 1 minute, send the detector to a service centre.

Technical specifications

Power 3 x AA 1.5V; 2.4Ah alkaline batteries

Typical lifetime approx. 3 years

Communication band 868.5 MHz, OASiS protocol

Communication range approx. 300 m (unrestricted area)

Dimensions diameter 126 mm, height 50 mm

Smoke detection optical light scattering

Smoke detector sensitivity m = 0.11 - 0.13 dB/m according to EN 54-7

Heat detection class A2 according to EN 54-5

Alarm temperature +60°C to +70°C

Operating temperature range -10°C to +80°C

Complies with EN 54-5, EN 54-7, EN 54-25,

Also complies with ETSI EN 300220, EN 50130-4

EN 55022, EN 60950-1

Can be operated according to ERC REC 70-03

1293-CPD-0250

JABLOTRON ALARMS a.s. hereby declares that the JA-82ST detector is in compliance

with the essential requirements and other relevant provisions of Directives 1989/106/EC

and 1999/5/EC. The original of the conformity assessment can be found at

www.jablotron.com

- Technical Support section

Note: Although this product does not contain any harmful materials

we suggest you return the product to the dealer or directly to the

producer after use. For more detailed information visit

www.jablotron.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-82ST Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info