Bedienungsanleitung Jablotron JA-82Y (Seite 8 von 13) (Englisch)

555059

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

The JA-82Y GSM communicator installers manual 8/8 MDL51108

• The communicator registration code xxxxx-xxxxx-xxxx. The code is stated

on the label on the communicator board, in the OLink application or you

can have it sent to you by SMS (see 6.23)

• The telephone number of the communicator SIM card

• The remote access password (see 6.24)

• When GPRS is not available a connection with OLink can be realized by

SMS with limited capabilities. After GPRS has been restored, the system

automatically starts to use the GPRS connection.

8.5. Time synchronizing process

The right and accurate time is taken from the GSM network via received SMS

messages or from the Jablotron YTUN server when GPRS is active. When the

communicator has not got time synchronization information, it sends an SMS to

itself via the GSM network (1x per 10 days). There is one requirement, the

communicator must have its own SIM card number saved in position 0 by the

sequence 81 0 xxx..x *0 (xxx..x = own telephone number). If you change the SIM

card, position 0 will be automatically erased.

Time synchronization (see section 6.17) of the control panel is performed

whenever entering into service mode or maintenance mode, and if there is a

difference greater than 5 minutes between the correct time and control panel time,

synchronization is performed automatically in an unset system without needing to

manually change modes.

Notes:

• Synchronization is indicated by a keypad beep

• PG outputs are deactivated during time synchronization, then the outputs

are reactivated afterwards.

• A time synchronization event is sent to the ARC by automatically entering

service/maintenance mode (even when unset) and CID report code 1625

(625 means a time and date reset based on the norm DC-05) is transmitted

before exiting service/maintenance mode.

9. Technical specifications

Power 12V DC (from the control panel)

Stand-by consumption (mean value) about 35 mA

(depends on the GSM signal strength)

GSM band QUAD-BAND, 850/900/1800/1900MHz

Complies in configuration CIE OASIS system with EN 50131-1, EN 50136-2-1

as follows: ATS 4, ATS 5 if CID protocol is used

and the repeating period is set to zero (Sequence 06p0)

Operating environment – indoor general (-10°C to 40°C) Class II

Security Grade 2

Safety EN 60950-1

EMC ETSI EN 301489-1, ETSI EN 301489-7

EN 55022, EN 50130-4

Radio transmissions ETSI EN 301419-1 and EN 301511

CLIP protocol (caller ID + SMS) ETSI EN 300 089

Can be operated according to GSM Regulations

JABLOTRON ALARMS a.s. hereby declares that the JA-82Y is in

compliance with the essential requirements and other relevant

provisions of Directive 1999/5/EC. The original of the conformity

assessment can be found at www.jablotron.com - Technical

Support section

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the producer after use. More detailed information

can be found at www.jablotron.com - Technical Support

section

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-82Y Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-82Y

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info