Bedienungsanleitung Jablotron JA-87P (Seite 1 von 1) (Englisch)

554905

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

The JA-87P dual zone outdoor wireless motion detector - curtain 1 MKU53102

The JA-87P dual zone outdoor wireless motion detector - curtain

The JA-87P wireless outdoor detector with curtain lens characteristics is

designed to indicate disturbances outside the building caused by human bodies. It

is a dual zone outdoor detector by Optex with a 5° angular width detection zone

which makes it very suitable for guarding narrow spaces such as balconies, French

doors, terraces, etc. It is supplemented with a transmitter compatible with JA-8x

OASiS systems. Both the detector and the transmitter are powered by a lithium

battery. The common power supply is beneficial as the low battery signal is

transmitted to a control panel as standard. The detector is equipped with three

TAMPER contacts (at the front on the detection part and the front and rear on the

transmission part), which immediately report opening of the detector cover or its

tearing from the place of installation. The detector can also have the anti-masking

function activated. The detector reports its current status via control transmissions

to the system.

Detector position and installation

The following instructions should be followed when selecting the place for detector

installation:

1. The detector should be attached to a vertical wall

2. The detector should be installed 0.8 – 1.2 m above the ground

3. The best movement detection is provided when the detection zones intersect

4. No other moving objects (bushes, trees, high grass, etc.) should be situated in

the field of sight of the detector. Avoid direct action by strong sources of light

(sun reflections).

Detector installation procedure

1. The detector consists of two

parts: the detecting one (1)

and the transmission one (2).

Their mutual position can be

adjusted according to the

picture. Punch holes for wires

in the plastic transmission

part of the detector

depending on which position

of the parts you have

selected (there are holes

indicated on the plastic for

this purpose).

2. Unscrew and remove the

detecting part cover. The

position of the detecting part

is fixed with a toothed plastic lug which should be moved upwards. Then remove

the whole part with the electronics by bending the upper part of the plastic and

pulling the swivel part towards you. You will thus make the installation holes

located under this part accessible.

Warning: Do not touch the sensors during handling

3. Pull the bundle of cables through the punched hole into the transmission part.

4. Attach the detecting and the transmission part to the wall using the supplied

screws (mind the correct orientation – marked with an upward-facing arrow on

the plastic).

5. Reassemble the detecting part.

6. Use the supplied self-adhesive plastic posts to attach the transmission module

to the bottom of the transmission part so that the function switch is located in the

top left corner. Place the DPS as high as possible – the bottom screw which

attaches the plastic base to the wall must be visible. You will thus avoid possible

interference with the antenna resulting in reduced detector range.

7. Use connectors to interconnect the wiring between the detector parts (cannot be

mixed up).

8. If you use the rear tamper (recommended), remove the jumper from the pins on

the board and plug in the tamper connector (regardless of polarity). The ring

magnet included in the package should be attached on the wall in the

corresponding position under the transmission part of the detector.

Switching on and enrolling the detector into the system

Rear tamper

connection

Switch No. 1

INSTANT

DELAYED

Switch No. 2

PULSE*

STATE

Vcc

TMP

INP

GND

detector

connection

LED

must be in

pulse mode

LITHIUM

3 / 3,6V AA

Study the control panel (receiver unit) installation manual before inserting the

battery. Use AA 3.6V lithium batteries only. The correct position of the battery is

indicated on the battery holder. When the battery has been installed, the

transmitter sends a signal which enrolls it to the control panel. The control panel

must be in enrollment mode at that time. Use switch no. 2 to set system reaction to

detected movement (ON = instant or OFF = delay). Switch no. 1 should remain in

the OFF position.

Setting up the optical part of the detector

A detection range of 5 m or 2 m can be set. The setting is done by turning the

bottom detector lens (closer to the centre of the cover). The lens shape is

designed so that its projecting part uncovers the detection distance which you have

selected when it is inserted back into the plastic base (see the picture below). Do not

turn the upper lens!

Other detector properties can be set using a switch in the detector

ON OFF

1 test mode normal operation

2 5 sec energy saving mode 120 sec

3 fault signal triggers N.O NC

4 LED enabled LED disabled

5 normal immunity of detection increased immunity of detection

6 anti-masking enabled anti-masking disabled

The default settings are in bold letters.

The detection part can be turned in a 190° range with locking after each 5°.

When the required angle has been set, use the plastic lug to prevent further

movement. The angle is fixed completely when the cover with the lenses is put

back and the screw is tightened.

Checking the status of and replacing batteries

The detector checks battery status and automatically reports a low battery to the

system. The detector remains fully functional. The batteries should be changed as

soon as possible (within 1 week).

The control panel must be in service or maintanace mode before you start

changing the battery. Use 3.6V AA batteries only. When the cover has been

closed, the detector switches to normal operating status

automatically.

Note: If you insert a nearly drained battery into the detector by mistake, the

sensor does not start working and this status is indicated with transmitter LED

flashing. If the battery is completely drained, the detector does not react at all.

Technical specifications

Power 1x type LS(T)14500 (AA 3.6 V / 2 Ah) lithium battery

Average battery lifetime approx. 3 years (with 120 s energy saving mode)

Operating frequency band 868 MHz

Range – distance from the control panel up to 300 m with direct visibility

Optex detector parameters

Detection characteristics 2 or 5 m / 5°

Recommended installation height 0.8 – 1.2 m

Object motion speed 0.3 – 1.5 m / s

Detector cover conformance IP55

Environment according to EN 50131-1 IV

Operating temperature range -20°C to +60°C

Max. relative humidity of the environment 95%

Security rating according to OPTEX

Complies with ETSI EN 300 220, EN 50130-4, EN 55022, EN 60950-1

Weight 190 g

Can be operated according to CTU VO-R/10/06.2009-11

Jablotron Ltd. hereby declares that the JA-87P is

in compliance with the essential requirements

and other relevant provisions of Directive

1999/5/EC. The original of the conformity

assessment can be found at www.jablotron.com

Technical Support section

Note: Although this product does not contain any

harmful materials we suggest you return the product

to the dealer or directly to the producer after use.

Jablotron JA-87P Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info