Bedienungsanleitung Jablotron JA-88P (Seite 1 von 2) (Englisch)

554798

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

JA-88P outdoor wireless motion detector 1 / 2 MKU52103

JA-88P outdoor wireless motion detector

The JA-88P wireless PIR detector is designed to indicate movement outside

the building caused by human bodies. It is based on an outdoor detector by

Optex supplemented with a transmitter compatible with JA-80 OASiS

systems. Both the detector and the transmitter are powered by three lithium

batteries and the low battery signal is transmitted to an control panel. The

detector is equipped with two TAMPER contacts (front and rear), which

immediately report opening of the detector cover or its possible tearing from

the place of installation. The detector regularly performs automatic tests and

reports its status to the control panel.

Installation

The following instructions should be followed when selecting a place for

detector installation:

 The detector must be installed in a position where its bottom surface is

parallel to the watched zone (either directly on the wall, or possibly, if a

change of direction is required, the supplied joint can be used). This

condition is essential for good immunity to false alarms. For more

information see Fig.1.



The detector should be installed 2.5 – 3 m above the ground.



No other moving objects (bushes, trees, high grass, etc.) should be situated in

the detection area of the detector. These objects can be masked out using the

supplied foils. Avoid direct action by strong sources of light (sun reflections).

You can use the supplied viewing hood for this purpose.

 When selecting the right place to install your detector, keep in mind that the best

movement detection is provided when the detection zones intersect (Fig.2).

PARALEL

2,5 ... 3m

TILT

Fig.1 and 2

1. Unfasten the curing screw on the bottom side of the upper cover and

remove it.

2. Pull the plastic tab under the lower PIR sensor slightly to remove the

optical part. Warning: Do not touch the detector sensing face during

handling.

3. Use a screwdriver to punch a hole on the right of the bottom detector

cover in order to pull the rear TAMPER cable through (supplied in the

package).

When installed without the joint holder:

 Use the Base Mounting Template from the box lid.

 Pull the rear TAMPER cable through the punched hole in the bottom

detector cover and fix a magnetic contact to the place according to the

template (Base side).

 Mark a place on the wall where you want to install the detector – i.e.

holes for the screws and the magnet (Wall side), and fix the magnet to

the wall.

 Fix the rear cover on the wall while checking the position of the

magnet and the reed contact (they should be as close as possible).

When installed with the joint holder:

 Use the Bracket Base Mounting Template from the box lid.

 Press the plastic tab to remove the screw cover (secured with a

plastic cord against falling during work ).

 Unscrew the securing screw (inside under the cover) to loosen the

joint and swivel it to one side to gain access to the installation

holes.

 Pull the rear TAMPER cable through the cavity in the joint and fix

the magnetic contact in the given place (between the plastic lugs).

 Mark a place on the wall where you want to install the detector – i.e.

holes for the screws and the magnet (Wall side), and fix the magnet

to the wall.

 Fix the joint holder to the wall while checking the position of the

magnet and the reed contact (they must touch).

 Now screw the bottom cover together with the joint holder. Remove

the central screw which blocks vertical movement and screw it

through a hole in the bottom cover.

Pull the rear TAMPER cable through the opening you have punched

in the bottom detector cover and insert the rear TAMPER connector

into the pins marked TMP IN (remove the jumper installed in

production).

Enrolling the detector to the system

The signal transmitter for wireless communication is located

underneath the optical part of the detector. The transmitter’s battery

case is not used; the batteries are inserted into the battery holder of

the motion detector. Use three AA 3.6V lithium batteries by the

same manufacturer and replace all three batteries at the same

time. The correct position of the batteries is indicated on the battery

holder. When inserting the batteries, it is necessary to remove the part

of the holder held in place with a metal lug. When the batteries have

been installed, the transmitter sends a signal which enrolls it to the

control panel (the control panel must be in enrollment mode at that

time – see the manual). Use switch no. 2 to set the system’s reaction

to any detected movement (ON = instant or OFF = delayed). Switch

no. 1 should be left in the OFF position

rear tamper

connector

Switch 1

INSTANT

DELAY

Switch 2

PULSE*

STATUS

Vcc

TMP

INP

GND

interconnection

to a detector

indication

Set pulse mode

battery not

used

Fig. 3 detector transmitter

BRACKET BASE

BRACKET

SHAFT COVER

BASE

BATTERY HOLDER

OPTICAL PART

PIR SENSOR

()

DO NOT TOUCH

IR ANTIMASKING

INSTALATION SCREWS

JOINT POSITION LOCKING

(DETECTOR TILT)

LED INDICATOR

MASKING FOIL

LENS

UPPER COVER

SECURING SCREW

PROTECTIVE HOOD

COVER SCREWS

JOINT POSITION LOCKING

(DETECTOR DIRECTION)

Fig.4 detector configuration

Jablotron JA-88P Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info