Bedienungsanleitung Jablotron JA-89P (Seite 1 von 2) (Englisch)

554818

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

The JA-89P wireless motion detector 1/2 MKU51102

The JA-89P wireless outdoor PIR detector

The JA-89P is an outdoor intruder detector designed to detect human body

movement in a protected area. It supplements a double-zone PIR sensor

produced by Optex with a Jablotron transmitter enabling the sensor to be

used within JA-80 OASiS systems. Both the PIR sensor and the transmitter

are powered by a lithium battery. Sharing the power source allows low voltage

reports to be transmitted to the control panel in the standard way. The

detector is equipped with two tamper sensors (front and back) capable of

signalling that the detector’s cover has been opened or that the detector has

been torn off its position. Self testing is performed automatically on a regular

basis including reporting detector status to the control panel. These properties

make the JA-89P a standard component of Jablotron’s OASiS system.

Installation

Choose a proper place for detector installation according to the following:

1. Install the detector perpendicular to the ground to make the upper

detection area parallel to the ground.

2. The installation height is 0.8 – 1.2 m.

3. Mount the detector so that the majority of traffic flow is across the

detection pattern.

4. Avoid positions where moving or waving objects like cars, plants or trees

might appear in the detection area. Avoid positions where the detector

can be affected by strong light sources, e.g. reflected sunlight.

3.1.1. 3.

0.8

1.2 m

Installation, step by step:

1. Unscrew the lock screw located on the bottom side of the upper cover and

remove the cover.

2. Unscrew the screws fastening the optical part of the detector and remove

this part by tipping it up.

3. Disconnect the rear tamper sensor cable.

4. You can fix the detector to an even plate using either two non-skimmed

holes or four skimmed holes located in the corners of the rear cover.

5. Use the drilling template supplied in the package for marking all the spots

relevant to detector fixing as well as to fixing the rear tamper magnet.

6. Alternatively, you can install the detector on a pole (Ø 43 – 48 mm) using

straps supplied with the package. However, this way of installation

disables the rear tamper switches (tear-off signalling) – you have to short

out the transmitter tamper inputs using a jumper.

7. After the bottom plastic cover has been fixed, insert the rear TAMPER

connector into the terminal marked TMP IN.

Caution: Never touch the detection surface of the PIR sensor.

Optical part

Upper cover

Lock screw

Fixing part

Adjustment switches

Rear tamper connection

Powering up and enrollment

The transmitter of wireless communication signals is located below the

detector’s optical part. Study the installation manual of the receiver (control

panel) first to learn how to enter enrollment mode. Only use a lithium battery

of type AA 3.6 V. The correct battery position is marked on the battery holder.

After a battery is inserted the transmitter sends an enrollment signal to the

receiver. The control panel – if used as a receiver – must be in enrollment

mode. You can use the detector’s switch No. 2 to configure control panel

reactions (ON = Instant, OFF = Delayed). Switch No. 1 should be OFF.

Rear tamper

connection

Switch No. 1

INSTANT

DELAYED

Switch No. 2

PULSE*

STATE

Vcc

TMP

INP

GND

detector

connection

LED

Set to

pulse mode

LITHIUM

3.6V AA

The JA-89P detector transmitter

Optical part adjustment

The detector’s optical part contains two PIR sensors each having its own

detection plane. The detection area angle of the lower sensor can be

configured over a wide range. The sensors operate with AND logic: an alarm

signal is generated only if both sensors are triggered (if both detection planes

are crossed). You can adjust the detection plane slope of the lower sensor by

a shifting lever according to the picture below.

distance 0 - 12 m

distance 0 - 2 m

distance 0 - 5 m

distance 0 - 8 m

The following table provides a summary of detection length

characteristics:

The lower sensor max. detection length

Position

Standard See note below:

A 10 m 8.0 to 12.0 m

B 8 m 6.0 to 10.0 m

C 5 m 4.0 to 5.5 m

D 2 m 1.5 to 2.5m

Note: The maximum detection length of the lower detection plane may

vary as above due to environmental thermal conditions. This must be

taken into consideration during detection range adjustment.

Protected area

Positions A,B,C,D

Unprotected area

Tolerance

The detection area angle is 90°. The direction can be adjusted in 15° steps

by rotating the detector’s plastic part. The detector lens covers the whole

angle of 180° - therefore it does not require any adjustment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-89P Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info