Bedienungsanleitung Jablotron JK-16 (Seite 2 von 2) (Englisch)

554868

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

JK-16 PROFI 2/4 MGK24401

4. Detector and accessory installation

a) Install the JA-60N magnetic detector onto the door

(antenna pointing up or down)

b) Install the JA-60P PIR motion detector

c) Select Instant or Delay reactions via the DIP switches

inside the detectors.

d) Connect the detector’s batteries (pull out the red tape to

activate the batteries)

e) Attach the keypad to the desired location

f) Plug the UC-260 wireless siren into a power socket

g) Test the wireless doorbell button and install it.

5. Enrollment of additional accessories

If you install additional detectors (max. 32), you have to enroll

them. The system should be in P mode (if not enter F0 6060):

a) Press 1 to enter enrollment mode*

b) The next free detector position will be displayed on the

keypad.

c) Install batteries into all new detectors step by step to enroll

them (system will automatically offer the next free position)

d) To scroll through sensor positions, press 1 (up) or 7 (down)

e) To enroll a second detector to an occupied position press 5

before you install the detector’s batteries

f) To exit enrollment mode press the N key

The wireless keypad (JA-63F) enrolls after you install its

battery while in enrollment mode.

The remote control (RC-4x) enrolls after you press and hold

both

and buttons while in enrollment mode.

The wireless outdoor siren (JA-63A) enrolls after it is

powered up while in enrollment mode

To enroll the control panel to UC receivers enter 299 on

the keypad while in P mode

Check individual device manuals for more details

• *Enrollment mode will also start after shorting the reset pins

in the control panel while it is in P mode.

6. Detector and controller testing

a) The system should be in P mode (if not enter F0 6060)

b) Trigger detectors – their addresses (1=door and 2=PIR) should

be indicated (if the PIR detector does not react, re-enter test

mode by opening and closing its cover)

c) Press button

on the RC-4x remote control – c2 will be

indicated

7. To measure the strength of the radio signal

a) While in P mode, press 1 and then using 7 scroll to position 1

b) Press 8 to start measuring

c) Activate the door detector to view its signal strength

d) Using the 1 key, scroll to the next position (2 PIR) and

check its signal strength (if the PIR detector does not react,

reenter its test mode by opening and closing its cover)

e) Repeat step d) to check all enrolled items. The wireless keypad

(c1) signal is indicated after you trigger its tamper. The remote

control (c2) is indicated after you press it’s

button.

f) Change the location of an item if its signal is lower than 2

g) Return to P mode by pressing the N key

8. Programming the system

a) The system should be in P mode (if not enter F0 6060)

b) Using the following sequences you can program:

Function Sequence Comments

Your installer code* 5 xxxx xxxx

6060 factory default

xxxx new code

Exit delay

20x

3=30sec factory def.

Entrance delay

21x

3=30 sec factory def.

Alarm duration

22x

4=4min factory def.

Time & date

4 hh mm DD MM YY

See control panel installation manual for more details.

• Must be changed

•

9. Finishing the installation

a) Fill in the information on the sticker label and attach it inside

the keypad cover.

b) Switch the system to standby (by pressing the N key)

c) Instruct the user on how to operate the system

attach

open

click

rear tamper

lever

Don't tight

this screw

2,5

1,5

0,5

1,6 3,7

range

[m]

height

[m]

120

zone A

zone B

zone C

zone A

zone B

zone C

JA-60P coverage

avoid locations against windows or close to a heater

JK-16 PROFI 3/4 MGK24401

10. Keypad operation

11. Specifications

Power 230 VAC, max 0.1 A, supervised, class II

Power supply A type (EN 50131-6)

Backup battery 12 V, 2.26 Ah, normal life time 5 years

Backup power output 13VDC, the max. permanent current is 0.4

or 1A for max. 15 min (1 cycle per hour),

Consumption of the control panel is 30 mA; JA-60E 25 mA

Hard-wired inputs 4 input zones, selectable triggering:

Wireless zones 16 zones (2 detectors can be enrolled to each

Wireless controllers max. 8 (JA-60F, RC-22, RC-44)

Access codes master code and 14 user codes.

Wired outputs Alarm relay dry contacts 1A/60V;

Programmable outputs PgX , PgY connect to the GND max. 0,1 A

Siren output 12 V, 0.7 A

Working frequency* 433.92 MHz; digital hopping code; supervised

communication

Comply with EN 50131-1, EN 50131-6

Security grade 2 (low to medium risk)

Environmental class II indoor – general (-10 to 40oC)

Safety EN 60950-1

EMC ETS 300683

Radio characteristics ETSI EN 300220

Can be operated according to ERC REC 70-03

Jablotron Alarms a.s. hereby declares that the JA-83K “OASiS“

control panel is in compliance with the essential requirements and

other relevant provisions of Directive 1999/5/EC. The original of

the conformity assessment can be found on the web site

www.jablotron.com, Technical Support section.

Note: Dispose of batteries safely depending on the type of the

batteries and local regulation. Although this product does not

contain any harmful materials we suggest you to return the

product to the dealer or directly to the producer after usage.

Entry Function

User code

Arming / Disarming (Setting\Unsetting)

F1 /

Arming without a code

F2 /

Partial arming

F3 /

Door lock opening

Memory reading

F5 New master code (example: F5 1234 2789 2789)

F6 User codes setting (example: F6 1234 03 3344)

F7 /

Disarming under duress

Appliance control (F81 = ON, F80 = OFF)

F0 M.code

User test mode (example F0 1234)

Escape & fault detail reading

Motion detector

JA-60P

Doors, Windows

JA-60N

Wireless keypad

JA-63F

Remote control

RC-4x

Indoor siren

UC-260

(230 V AC)

Control panel

JA-63KR

Power (230 V AC)

Jablotron JK-16 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info