Bedienungsanleitung Jablotron RC-85 (Seite 1 von 1) (Englisch)

554856

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

The RC-85 transmitter (car accessory) MKF51001

10R - 01 4531

The RC-85 transmitter (car accessory)

The RC-85 is a component of Jablotron’s Oasis 80 alarm

system. It is designed to be installed inside cars with a voltage

supply of 12 to 24 V to remotely control electrical appliances

(e.g. garage doors or parking gates), in a similar way to the RC-

86 keyfob. It can also be used for sending an alarm signal from

a car.

The transmitter is not continuously powered and only transmits

a signal when connected to the power supply. It can be

configured whether a signal is sent instantly or only after two

applications of the power supply within 2 seconds.

Installation

Install the transmitter into the car’s interior (e.g. in the dash-

board) It should not be installed directly onto a metal surface (it

adversely affects the transmitter’s radio range). We recommend

securing the transmitter onto a plastic part of the car with

screws. The wires also serve as an antenna so they should not

be shorter then 30cm.

Wiring

Black GND

Red

Connecting to a positive voltage

supply sends a SET (arm) signal

White

Connecting to a negative voltage

supply sends an UNSET (disarm)

signal

By connecting both wires to a voltage supply a

panic signal is sent (= both buttons are pressed

simultaneously).

 For operation in a car it is possible to use existing switches

in the car (full-beam headlight flash switch, horn – it is

recommended to have the double-pulse reaction enabled),

or, alternatively, any other suitable additional switches can

be installed.

RC-85

red

optical

horn

+12V

full-beam

black

white

Example of wiring in a car

 To send alarm information from a car to an Oasis

system, connect the red and white wires to the car

alarm output where a positive voltage supply is present

during an alarm (e.g. the siren output).

Caution: Avoid using this output for confirming car

alarm operation (this would cause false alarms).

Double-pulse reaction

As a factory default, the transmitter will send a signal

immediately after being connected to a power supply. This

behaviour can be changed by connecting a jumper (link) inside

the transmitter. After that, both inputs will react only when a

voltage supply is connected for the second time within 2

seconds. This corresponds to a double-press of a button. This

feature allows you to prevent the appliances from reacting to

changes in voltage supply which are due to standard car

operation, e.g. turning lights on/off. If both inputs are switched

simultaneously to a voltage supply, a panic signal is always sent

immediately after the power supply has been connected for the

first time, regardless of the jumper setting.

Enrollment to a receiver

Enrolling the RC-85 transmitter is the same as in the case of the

RC-86 keyfob. But instead of pressing the buttons, the two

wires get connected to a voltage supply.

Notes about RC-85 functions

The RC-85 only sends a signal at the moment of

connecting the wires to a voltage supply. For the next

transmission, the voltage supply must first be disconnected and

then connected again. The functions of each wire are

independent – if one wire is permanently connected to a voltage

supply, the other one still works.

For controlling appliances, the UC-82 or AC-82 receivers can

be used (the transmitter is enrolled to the receiver by activation

– see the manual for the particular receiver).

For acoustic signalling, the doorbell function of the JA-80L

indoor wireless siren can be used (the transmitter is enrolled to

the siren by activation – see the manual for the siren).

For reporting a car alarm to an Oasis alarm system, the

transmitter can be enrolled to the Oasis control panel or to the

UC-82 receiver. In enrollment mode, connect both RC-85 wires

(red and white) to a positive voltage supply and keep them

connected for about 3 sec. (the same effect as simultaneously

pressing and holding a keyfob’s buttons).

When the car alarm is triggered connect power to the red wire

to transmit a signal. The device reaction in the Oasis system is

set to 4 (24 hours).

Technical specifications

Power supply 12V to 24V ± 30%

Consumption 10 / 20 mA

Communication band 868 MHz, Oasis protocol

Communication range approx. 50 m (open area)

Config. input reactions 1 or 2 pulses of voltage supply

Operational temperature range -10 to +40°C

Storage temperature range -40 to +85 °C

Dimensions, weight 84 x 53 x 25 mm, 120 g

Can be operated according to ERC REC 70-03

FCC ID VL6RC85

JABLOTRON ALARMS a.s. hereby declares that the RC-85 is in

compliance with the essential requirements and other relevant provisions of

ECE Regulation No.97.00 and Directive 1999/5/EC and complies with

part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must

accept any interference received, including interference that may cause

undesired operation.

CAUTION: Changes or modifications no expressly approved by Jablotron

could void the user´s authority to operate the equipment. The original of the

conformity assessment can be found at www.jablotron.com, Technical

Support section.

Note: Although this

product does not

contain any harmful

materials we suggest

you return the

product to the dealer

or directly to the

producer after use.

Jablotron RC-85 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info