Bedienungsanleitung Jablotron RC-87 (Seite 1 von 1) (Englisch)

554858

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

The RC-87 wireless wrist button MKT51001

The RC-87 wireless wrist button

The RC-87 is a component of Jablotron’s Oasis 80 alarm system.

It allows users to trigger panic alarms or to control appliances

remotely. It is especially designed for personal calls for help. The

battery-powered wireless button communicates via OASIS radio

protocol.

The button can be worn on your wrist like a watch or it can hang

around your neck (an appropriate strap is supplied in the package).

Caution: When hanging around the neck, the strap must be

equipped with a mechanical release which disconnects the strap

whenever the loading force exceeds 40N.

Enrolling to an Oasis control panel

The button can be used with an Oasis control panel for triggering

panic alarms. Take the following steps to enroll the button:

1. Enter enrollment mode on the control panel by keying in “1” in

Service mode (the desired device address can be chosen by the

arrow keys).

2. Hold the button until you see the button’s LED flash once.

3. The button will enroll to the chosen position.

4. Exit enrollment mode by pressing “#”.

The control panel’s natural reaction to the button is a Panic alarm. A

different reaction can be programmed if desired.

The wrist button can be enroled by inserting the battery (step 2).

Functionality

By factory default, the button reacts to pressing with beeps and

flashes. This way it is signalled that the time is getting close for alarm

triggering. If you re-press the button within 5 seconds, the pre-

alarm condition will be cancelled. If no cancellation occurs, an alarm

signal will be sent after 5 seconds. This feature allows the user to

cancel accidental button pressing.

The button can be reconfigured to another function as follows:

1. Open the button unit (release 4 screws from below) and pull out

the electronics.

2. Disconnect the battery from the holder (it can be pulled out using

a thin tool). Wait for 15 seconds.

3. Press and hold the button with one hand and insert the battery

with your other hand. Keep the button pressed until beeps are

heard (after 2 seconds approximately). The number of beeps (1, 2

or 3) indicates the mode which has been set, see below.

1 beep The button will beep and flash 5 seconds after being

pressed (this mode allows the cancelling of accidental

pressing).

2 beeps Respond to a single press instantly by triggering an

alarm and sounding a single beep.

3 beeps Respond to a single press instantly and silently by

triggering an alarm.

Choose the desired function by repeating steps 2 and 3, then

reassemble the button. This configuration will not be affected by

normal battery replacement (reconfiguration is only possible in the

above way).

Testing the panic button

The signals received by the control panel from the RC-87 can be

checked and measured. See the control panel manual for details.

Controlling electrical appliances

The RC-87 can also be used with other Jablotron products which

communicate via Oasis radio protocol, e.g. the JA-80L wireless siren,

or relay receiving modules series UC-8x and AC-8x (see the manuals

of these particular products for details).

The RC-87 transmits the same kind of signal as transmitted when

a pair of buttons is pressed simultaneously on an RC-80 keyfob.

The RC-87 can be enrolled to several receivers at once, e.g. alarm

triggering can also cause lights to be turned on.

Battery replacement

The button unit monitors its battery voltage and if too low, a report

is sent to the control panel to inform the installer or user. A critical

voltage level is also indicated by an LED flashing fast 3 times every 5

minutes. The battery should be replaced as soon as possible. As with

configuration, the button can be opened by unscrewing the 4 screws

from the bottom part. We recommend battery replacement be done by

a service technician.

Expired batteries should not be thrown into the garbage, but

disposed of according to local regulations.

Technical specifications

Voltage lithium battery type CR 2032 (3.0 V / 0.2 Ah)

Typical battery lifetime approx. 3 years (for 1 daily activation maximum)

Communication band 868 MHz, Oasis protocol

Communication range approx. 50 m (open area)

Environment external protected

Housing IP-44

Operational temperature -25 to +50 °C

Can be operated according to ERC REC 70-03

Complies with EN 300220, EN 50130-4, EN 55022,

EN 60950-1, EN 50134-2

FCC ID VL6RC87

JABLOTRON ALARMS a.s. hereby declares that the RC-87 is in

compliance with the essential requirements and other relevant

provisions of Directive 1999/5/EC and complies with part 15 of

the FCC rules. Operation is subject to the following two

conditions: 1. This device may not cause harmful interference,

and 2. This device must accept any interference received,

including interference that may cause undesired operation.

CAUTION: Changes or modifications no expressly approved by

Jablotron could void the user´s authority to operate the

equipment. The original of the conformity assessment can be

found at www.jablotron.com, Technical Support section.

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the producer after use. See www.jablotron.com for

details.

Jablotron RC-87 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info