554826

Jablotron TP-83 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
TP-83 programmable wireless thermostat 2 / 2 MKL51904
4. M4 – Service menu
This menu allows for the configuration of parameters which usually
stay fixed during normal operation. When the service menu is entered,
the
symbol is shown on the display. The menu contains 9 items
(they can be scrolled through by turning the knob). Each of the first 7
items corresponds to a parameter which can be configured in a
standard way (by pressing the knob, turning the knob until the desired
value is displayed, and re-pressing the knob).
The SPAN parameter allows you to configure
the hysteresis – the accuracy to which the
temperature is regulated. One of the following
accuracy ranges can be selected: ±0.1˚C,
±0.2˚C or ±0.5˚C (the factory default setting is
±0.2˚C).
Example:
If the accuracy is adjusted to ±0.5˚C and the temperature is
set to 24˚C, the thermostat switches the heating on when the
temperature drops below 23.5˚C and it switches it off if the
temperature goes above 24.5˚C. In reality the temperature scatter can
be slightly higher because of the temperature persistence of the room.
Warning: too high an accuracy can cause the heating to turn on
and off too frequently.
The t Lo parameter is the lower limit to which
the economical temperature can be set. In
addition, any drop in temperature under t Lo
causes a “heat to t Lo temperature” signal to
be transmitted.
The t Hi parameter is the upper limit to which
the Comfortable temperature can be set.
The AL Lo corresponds to the critically low
temperature. Any drop in temperature under
AL Lo causes a Panic signal to be sent to the
receiver (reporting a frost threat).
AL Hi corresponds to the critically high
temperature. Any rise in temperature above
AL Hi causes a Fire signal to be sent to the
receiver.
The Corr parameter allows for a correction of
possible temperature measurement offsets.
The range of adjustable corrections is ±1°C.
This parameter allows you to enable or
disable thermostat adaptive mode. If enabled,
the thermostat switches on in advance
according to the temperature persistence of
the heating system.
Selecting this item and pressing and holding
the knob for 5 seconds resets the thermostat
to the factory default settings.
By selecting OK and pressing the knob the
menu is escaped from.
The parameter ranges are restricted according to the following table:
Parameter Adjustment
range
Factory
default
Description
SPAN 0.1°C;0.2°C;0.5°C 0.2°C Hysteresis for
switching
t Lo +6°C to +40°C* 6°C Lower limit of
t Hi +6°C to +40°C* 40°C Upper limit of
AL Lo –9°C to +20°C 3°C Panic alarm
AL Hi +30°C to +70°C 60°C Fire alarm
Corr
±1°C
0 Correction
Auto On/OFF On Adaptive mode
+6°C to +40°C 18°C Economical
temperature
+6°C to +40°C 21°C Comfortable
temperature
* t Lo to t Hi and to must be valid ranges: t Lo must not be
greater than t Hi and
must not be greater than .
Party mode
You can put the thermostat into party mode by
briefly pressing the knob (indicated by
symbols
and together). After then the
thermostat maintains the Comfortable
temperature increased by 2°C.
Party mode terminates whenever a switch to Economy temperature
regulation occurs (whether manual or scheduled).
Displaying the set temperature
When not being handled, the thermostat shows the current
temperature in the room. If you want to display the temperature which
is set for the current time, turn the knob. The set temperature will then
flash on the display for 3 seconds.
Battery replacement
Replace the battery when the low-battery symbol is displayed (or the
thermostat stops working). If the thermostat is enrolled to the control
panel, then a low battery will be indicated by the control panel (to the
user and installer). Only use AA 1.5V alkaline batteries.
Integration into the OASiS system
• The thermostat can be enrolled to a control panel as a detector.
If the temperature decreases below AL Lo a panic alarm will be
triggered = frost threat (heating failure).
• If the temperature exceeds AL Hi then a fire alarm will be
triggered.
• An AC-82 receiving unit has two output relays (X and Y).
Thermostats can be enrolled separately to each relay in order to
control two independent heating circuits.
• To operate a heating system the Oasis control panel can also
be enrolled (sequence 299) to the same relay of the receiving unit
as the thermostat is enrolled to. A thermostat enrolled to the X relay
can be operated via the PGX programmable output, and a
thermostat enrolled to the Y relay operated via PGY. If the
programmable output of the control panel is switched on, the
thermostat maintains the programmed temperature. If the control
panel’s output is switched off the thermostat only triggers heating
if the temperature drops below t Lo.
• To operate the heating, RC-80 or RC-88 remote controls can
also be enrolled to a receiving unit (AC-82). The heating can be
switched on by remote controls to heat to the desired temperature
and also switched off where it only heats when the temperature
is below t Lo.
• To disable heating when windows are open JA-80M or JA-82M
detectors can also be enrolled to the same relay as the thermostat
is enrolled to. If the windows are closed it heats to the desired
temperature and if windows are open it heats only when the
temperature is below t Lo.
• Up to 8 thermostats can be enrolled to a single relay. If at least
one thermostat transmits a heat command then the relay will be
switched on.
Specifications
Power supply: 1x AA 1.5 V alkaline battery
Battery lifetime typically 1 year
Temperature measurement: +6°C to +40 ˚C
Temperature accuracy: adjustable: ± 0.1, ± 0.2 or ± 0.5 ˚C
Freeze alarm (panic transmission) temperature threshold: < AL Lo
configurable from –9°C to +20°C
Fire alarm temperature threshold: > AL Hi
configurable from +30°C to +70°C
Operational frequency: 868 MHz, Oasis protocol
Operational radio range: up to 100 m (open area)
Operational temperature range: -10°C to + 70°C (low humidity)
Dimensions: 66 x 90 x 22 mm
Complies with
ETSI EN 300220, EN50130-4, EN55022, and EN 60950-1
Can be operated according to ERC REC 70-03
Jablotron Ltd. hereby declares that the TP-83 is in compliance
with the essential requirements and other relevant provisions of
Directive 1999/5/EC. The original of the conformity assessment
can be found on the web site www.jablotron.com
, Technical
Support section.
Note: Dispose of batteries safely
depending on battery type and local
regulations. Although this product
does not contain any harmful
materials we suggest you return the
product to the dealer or directly to
the manufacturer after use.
Mo
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Jablotron TP-83 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info