Bedienungsanleitung Jablotron TP-83IR (Seite 2 von 2) (Englisch)

554827

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

TP-83IR programmable wireless thermostat 2 / 2 MKL53301

The t Lo parameter is the lower limit to which the

economical temperature can be set. In addition,

any drop in temperature under t Lo causes a

“heat to t Lo temperature” signal to be

transmitted.

The t Hi parameter is the upper limit to which the

Comfortable temperature can be set.

Floor sensor ON/OFF

Lower floor-temperature threshold

Upper floor-temperature threshold

Current temperature of the floor (displayed after

pressing the knob)

The AL Lo corresponds to the critically low

temperature. Any drop in temperature under AL Lo

causes a Panic signal to be sent to the receiver

(reporting a frost threat).

AL Hi corresponds to the critically high

temperature. Any rise in temperature above

AL Hi causes a Fire signal to be sent to the

receiver.

The Corr parameter allows for a correction of

possible temperature measurement offsets. The

range of adjustable corrections is ±1°C.

This parameter allows you to enable or disable

thermostat adaptive mode. If enabled, the

thermostat switches on in advance according to

the temperature persistence of the heating

system.

Selecting this item and pressing and holding the

knob for 5 seconds resets the thermostat to the

factory default settings.

By selecting OK and pressing the knob the menu

is escaped from.

The parameter ranges are restricted according to the following table:

Parameter Adjustment range Factory

default

Description

SPAN 0.1°C;0.2°C;0.5°C 0.2°C Hysteresis for switching

t Lo +6°C to +40°C* 6°C Lower limit of

t Hi +6°C to +40°C* 40°C

Upper limit of

FL On/Off On Floor sensor ON/OFF

FL Lo +6°C to +40°C* 22°C

Lower floor-temperature

threshold

FL Hi +6°C to 40°C* 27°C

Upper floor-temperature

threshold

AL Lo –9°C to +20°C 3°C Panic alarm

AL Hi +30°C to +70°C 60°C Fire alarm

Corr

±1°C

0 Correction

Auto On/OFF On Adaptive mode

+6°C to +40°C 18°C Lower temperature

+6°C to +40°C 21°C Comfortable temperature

* t Lo to t Hi and to must be valid ranges: t Lo must not be greater than

t Hi and

must not be greater than .

Floor heat detection

If enabled by setting FL On, floor temperature detection is performed using an

IR sensor. The FL Lo and FL Hi parameters allow you to set temperature

thresholds for under-floor heating regulation:

• If the current floor temperature is lower than FL Lo, the thermostat will

switch the heating on. This way a comfortable floor-temperature is

maintained even if no switch-on request is generated due to the room

temperature.

• If the current floor temperature is higher than FL Hi, the thermostat will

switch the heating off. This prevents the floor from being damaged by too

high a temperature.

Note: Floor heat detection is of higher priority than room temperature

detection. This means that the current temperature in the room is taken into

account only when the current floor-temperature is between FL Lo and

FL Hi.

You can display the current floor temperature by entering the menu, scrolling to

the FL t parameter and pressing the knob (a re-press will cause a return to the

menu).

Party mode

You can put the thermostat into party mode by

briefly pressing the knob (indicated by symbols

and together). After then the thermostat

maintains the Comfortable temperature increased

by 2°C.

Party mode terminates whenever a switch to Economy temperature regulation

occurs (whether manual or scheduled).

Displaying the set temperature

When not being handled, the thermostat shows the current temperature in the

room. If you want to display the temperature which is set for the current time,

turn the knob. The set temperature will then flash on the display for 3 seconds.

Battery replacement

Replace the battery when the low-battery symbol is displayed (or the

thermostat stops working). If the thermostat is enrolled to the control panel, then

a low battery will be indicated by the control panel (to the user and installer).

Only use AA 1.5V alkaline batteries.

Integration into the OASiS system

• The thermostat can be enrolled to a control panel as a detector. If the

temperature decreases below AL Lo a panic alarm will be triggered = frost

threat (heating failure).

• If the temperature exceeds AL Hi then a fire alarm will be triggered.

• An AC-82 receiving unit has two output relays (X and Y). Thermostats can be

enrolled separately to each relay in order to control two independent

heating circuits.

• To operate a heating system the Oasis control panel can also be enrolled

(sequence 299) to the same relay of the receiving unit as the thermostat is

enrolled to. A thermostat enrolled to the X relay can be operated via the

PGX programmable output, and a thermostat enrolled to the Y relay

operated via PGY. If the programmable output of the control panel is

switched on, the thermostat maintains the programmed temperature. If the

control panel’s output is switched off the thermostat only triggers heating if

the temperature drops below t Lo.

• To operate the heating, RC-80 or RC-88 remote controls can also be

enrolled to a receiving unit (AC-82). The heating can be switched on by

remote controls to heat to the desired temperature and also switched off

where it only heats when the temperature is below t Lo.

• To disable heating when windows are open JA-80M or JA-82M detectors

can also be enrolled to the same relay as the thermostat is enrolled to. If the

windows are closed it heats to the desired temperature and if windows are

open it heats only when the temperature is below t Lo.

• Up to 8 thermostats can be enrolled to a single relay. If at least one

thermostat transmits a heat command then the relay will be switched on.

Specifications

Power supply: 1x AA 1.5 V alkaline battery

Battery lifetime typically 1 year

Temperature measurement: +6°C to +40 ˚C

Temperature accuracy: adjustable: ± 0.1, ± 0.2 or ± 0.5 ˚C

Freeze alarm (panic transmission) temperature threshold: < AL Lo

configurable from –9°C to +20°C

Fire alarm temperature threshold: > AL Hi

configurable from +30°C to +70°C

Operational frequency: 868 MHz, Oasis protocol

Operational radio range: up to 100 m (open area)

Operational temperature range: -10°C to + 70°C (low humidity)

Dimensions: 66 x 90 x 22 mm

Complies with ETSI EN 300220, EN50130-4, EN55022, and EN 60950-1

Can be operated according to ERC REC 70-03

JABLOTRON ALARMS. hereby declares that the TP-83IR is in

compliance with the essential requirements and other relevant

provisions of Directive 1999/5/EC. The original of the conformity

assessment can be found on the web site www.jablotron.com

Technical Support section.

Note: Dispose of batteries safely

depending on battery type and local

regulations. Although this product

does not contain any harmful

materials we suggest you return the

product to the dealer or directly to

the manufacturer after use.

Jablotron TP-83IR Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info