Bedienungsanleitung Jablotron UC-216 (Seite 1 von 2) (Englisch)

554913

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Wireless Control Receiver UC-216 1/2 MEJ52103

Wireless Control Receiver UC-216

Description

The UC-216 is a three channel receiver of coded radio signals. The status

of its two output relays and its output transistor is indicated on the front

panel. Up to 20 remote controls (RC-11, RC-22) can be taught to the unit.

There are three different operating modes available for the remote controls.

This allows the UC-216 to be used as a control for an alarm system, for

remote gate opening, garage door control, panic switch etc. A floating code

ensures a high security of transmission.

The UC-216 can also be used as a receiving unit for JA-60 wireless

system items. This use, for example, allows an existing wire-operated alarm

system to be extended with additional wireless detectors, wireless access

control keypads, etc.

Specifications:

Operating voltage: 12-24 V DC or 15 V AC

Power consumption: standby 0.25 W

max. 1 W (both relays activated)

Operating frequency: 433.92 MHz

Coding: digital, each remote control or JA-60 item has

a unique floating code

Output relays: Max. 120 V / 1 A

Output transistor: Max. 40 V / 0.2 A

Range (open area) : with RC-11 up to 30 meters

with JA-60 items, up to 100 meters

Working temperature from -10 to +40°C indoor use only

Can be operated according to ERC REC 70-03

Hereby, Jablotron Ltd., declares that this UC-216 is in compliance with

the essential requirements and other relevant provisions of Directive

1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.cz, section Technical support.

Installation:

Open the external cover of the unit by pressing in the internal tab of

the lock on the top (small flat screw-driver is appropriate). Loosen the

central screw and remove the PCB. Route the wires through the hole in

the bottom of the rear housing. Attach the housing to the desired place

using the provided screws.

Terminals description:

TAMPER tamper switch output (max. 24 V / 100 mA)

OUT output of NPN transistor to GND

NC, NO, C output relay dry contacts (X and Y)

+U, GND power voltage 11-24VDC or 15VAC

The status of relay X, relay Y and the OUT is indicated by 3 LED

indicators on the front cover. When active, the corresponding LED

lights.

RC-11, RC-22 mode

Remote controls enrolling - you can

enroll up to 20 different RC-11 or RC-22

remote controls to the UC-216 unit. There

are two buttons on each remote control

(A and B), enabling each remote control

to send two different commands by

pressing button A or B. The RC-11 can

also send a third command by pressing

the A & B button simultaneously (not

available with the RC-22).

There are two setting buttons in the

UC-216. Button X is used for relay X

teaching; button Y is used for relay Y

teaching. By pressing the setting button

you can scroll through the three learning

(operating) modes (1 to 3) indicated by a

corresponding flashing indicator.

By pressing a button on the remote

control while a desired UC-216 learning

mode is selected, you enroll that button to

the receiver’s memory. The corresponding

operating mode will now be associated

with this remote control button.

Operating modes available (valid for X and Y relays)

MODE reaction of the relay

when RC button pressed

which RC

button can be

taught

1 pulse

relay will turn on for 2 seconds A, B, A&B

2 latch

relay status will change to the

opposite (ON/OFF/ON...)

A, B, A&B

3 ON - OFF

button A turns relay on, button B

turns relay off

A or B

Setting remarks

• new RC button enrollments are added to previously enrolled ones

• after 20 RCs are taught, no other remote can be added

• double flashing of the LEDs indicates a full memory

• if one button is taught for multiple modes, only the last taught mode

will remain in the UC-216’s memory

• you can combine different modes with different RC buttons

• the output OUT can be activated only by simultaneous pressing of

the A&B buttons on the RC-11, only if the A button was enrolled for

relay X and the B button for relay Y. The OUT mode is the same as

the selected mode of relay X. This way three independent outputs

can be controlled.

• A selected setting mode will close after an RC button is enrolled,

or automatically after 10 seconds.

• All UC-216’s can operate with only remote controls or JA-60 items.

Combined operation is not available.

Note: A remote control taught to the UC-216 can also be used for

other devices. For example: the remote control of Jablotron’s Accent car

alarm can not only control your car with buttons A and B, but can also

control another device, if the simultaneous pushing of A&B buttons has

been taught to a UC-216 controller.

Garage door or gate opener mode

The UC-216, in combination with RC-11

or RC-22 remote controls, has an optional

mode to control garage door or gate

actuators. This mode is only available when

the UC-216’s memory is erased. By

pressing the UC-216’s X setting button,

scroll until both LED’s 1 & 2 are

simultaneously flashing. Then, by pressing

any button of the remote control, you teach

it to the UC-216.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron UC-216 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info