Bedienungsanleitung Jablotron UC-222 (Seite 1 von 2) (Englisch)

554926

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Wireless Remote Controller UC-222 1 / 2 MDU51104

Wireless Control Receiver UC-222

Description

The UC-222 is a single channel receiver of coded radio signals. It is pow-

ered by 230VAC (110VAC). Its output relay contact operates at 230VAC.

The UC-222 can be used with remote controls (RC-40,RC-11, RC-22)

and with the JA-60 wireless system items (detectors, keypads, control

panels). The UC-222 has four different operating modes and up to 30

different wireless items can be enrolled to the receiver’s non-volatile mem-

ory.

Specifications:

Operating voltage: 230 V ~ 50 Hz, Class II

Power consumption: 0.03 A (1 VA) / 0.05 A (1.8 VA)

Operating frequency: 433.92 MHz

Coding: digital, each item has a unique floating code

Output relay: over switching dry contact

Fused 6A at 250 V

Range (open area): with RC-11, 22 & 40 up to 30 meters

with JA-60 items up to 100 meters

Can be operated according to ERC REC 70-03

Complies with: ČSN EN 60 950, ETSI EN 300 220, ETS 300 683

Hereby, Jablotron Ltd., declares that this UC-222 is in compliance with

the essential requirements and other relevant provisions of Directive

1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.cz, section Technical support.

Installation:

Use a flexible double insulated cable (cross section 0.75 – 1.5 mm

) for

power supply connection.

• Open the external cover of the unit by pressing in the internal tab of the

lock on the top (small flat screw-driver is appropriate). Unscrew the cen-

ter screw of the internal safety cover and remove this cover.

• Route wires (not connected to power supply!) through the hole in the

bottom of the rear housing. Attach the housing to the desired place us-

ing the provided screws.

• Fix the wires in the power supply terminals. Replace the internal cover.

Mode

indicators

230 V~

50 Hz

Output

Setting

button

Relay

max. F6.3 A / 250 V

C NC NO

Terminal description:

NC, NO, C - output relay contact (fused for 6A)

PE - pair of connected terminals - Protective Earth (Ground)

N, L - power 230V / 50Hz

Setting

There is a setting button on the internal cover of the UC-222 and four

LED indicators. By pressing this setting button, you can scroll through

four learning (operating) modes (1 to 4) indicated by a corresponding

flashing LED indicator. When the selected mode’s LED is flashing, the

wireless item (remote control, detector etc.) can be enrolled (see

following description). As a maximum, 30 different items can be en-

rolled (assuming it is not specified for a particular item or mode).

UC-222 operating (learning) modes available

n. mode UC-222 relay reaction possible to enroll

(max. 30 items)

short

pulse

relay will turn on for 2 seconds

• RC buttons A, B, A&B

• detectors JA-60

• keypads JA-60D

long

pulse

relay will turn on for 2 minutes

• RC buttons A, B, A&B

• detectors JA-60

• keypads JA-60D

3 latch

relay status will change

(on - off - on -off .... )

• RC buttons A, B, A&B

• Keypads JA-60D

OFF

button A will turn relay on, button

B will turn relay off

JA-60M - follows sensor status

JA-60D code=on/off & F1=on

• RC with button A

• control panels JA-60*

• keypads JA-60D*

• detectors JA-60M*

* this item can not be combined with any other model and a max.of 8

items can be enrolled in this mode

Remote controls enrollment

Remote controls RC-40, RC-11& RC-22 can be used with the UC-222

unit. There are two pairs of buttons on each RC-40 (A & B and 1 & 2),

enrolling of desired pair of buttons will enable to each remote control to

send two different commands by pressing buttons A or B (1 or 2). RC-

40 can also send third command by pressing the A & B (1 & 2) buttons

simultaneously (not available with the RC-22).

By pressing a button on the remote control while a desired UC-222

learning mode is selected, you teach that button to the receiver’s

memory. The corresponding operating mode will now be associated to

this remote control button.

JA-60 detectors and keypads enrollment

Wireless detectors of theJA-60 system and the JA-

60D keypads can be taught to the memory in learning

mode no. 1 and 2 (pulse modes):

• remove the batteries from the JA-60 item

• select the desired learning mode of the UC-222 (no. 1

or 2)

• reinstall the batteries into the JA-60 item (in the JA-60P

detector, press and hold pressed its tamper switch while

installing the batteries)

• UC-222 will store the JA-60 items code in its memory

• close the cover of the JA-60 item

You can combine multiple JA-60 items and RC-40,

RC-11 & RC-22 remote controls to operate a UC-222 (up to thirty).

Note: If you have a JA-60 alarm system installed, its detectors can

also be simultaneously used for house automation. For example, a JA-

60P motion detector(s) can be taught to mode no. 2 of the UC-222

which controls a light. This way the detectors not only informs your

alarm control panel about detected movement, but also automatically

turn on lights in the corresponding area.

The JA-60D keypad can also be enrolled in learning mode 3 and 4.

Each entering of a valid access code on the JA-60D will change the

condition of the UC-222 relay. If the keypad was enrolled in mode 4,

then the entering of F1 on the keypad will switch the UC-222 relay on

(a max. of 8 keypads can be enrolled in this mode and they can not be

combined with other items).

If a JA-60N detector is enrolled in mode 4, then the UC-222 relay

follows the condition of JA-60N sensor (or INP terminal). As a maximum

8 JA-60N detectors can be enrolled in this mode.

JA-60K control panel enrollment

The UC-222 can also be used as a wireless output module for the JA-

60K control panel. The UC-222 will have the same function as the PgX

programmable output of the control panel. When you want to use the

UC-222 with the control panel, all other items have to be erased from

the UC-222’s memory. The control panel can be taught to the UC-222

only in learning mode no. 4:

• enter the programming mode on the JA-60K

• select learning mode no. 4 of the UC-222

• enter the code 299 on the JA-60K keypad

• the UC-222 will store the JA-60K code in its memory

• exit the JA-60K programming mode

Jablotron UC-222 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info