Bedienungsanleitung Jablotron UC-260 (Seite 1 von 2) (Englisch)

554845

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

UC-260 Wireless Acoustic Indicator 1 / 2 MFI51300

UC-260 Wireless Acoustic Indicator

The UC-260 can be used as a wireless indoor siren, a melody

doorbell or as a chime. It can also function as a small house alarm. The

UC-260 is compatible with Jablotron wireless control panels (JA-60 and

JA-65), JA-60 wireless detectors and RC-11, RC-22 and RC-28 remote

controls. Several triggering devices can be used simultaneously and

different melodies can be assigned to each device. Two different sound

levels can be selected. The UC-260 provides entrance and exit delay

chirps too, when used with a control panel.

Specification

Power supply 230 V, 50 Hz

Power consumption 1.5 W

Acoustics 8 melodies and/or 110 dB/m alarm siren

Input wireless devices max. 8 remote controls or detectors

1 control panel JA-60 or JA-65

Class II according to EN60950

Working frequency 433,92 MHz

Environmental conditions interior –10 to +40°C

Safety standards IP40 according to EN 60529, IEC 529

Installation

UC-260 is powered directly from a power outlet. The device should

not be installed close to any metal structures or other objects

obstructing radio signal transmission.

Enrolling of wireless components

1. Press and hold the button on the top of the UC-260.

2. Plug in the UC-260 to an outlet and hold the button until you hear

2 beeps.

3. Release the button – The button will begin to flash, indicating it is in

the programming mode.

4. Enrolling of components:

• Doorbell button (RC-11, RC-22, RC-28) can be enrolled by

pressing a button on the controller. Multiple pressing of the

controller’s button will allow you to scroll to a desired melody.

• Detector - chime mode (JA-60 detectors) can be enrolled by

inserting batteries into a detector. If you remove the batteries and

insert them again you can scroll to a desired melody (wait for 10

seconds before reinsertion).

• Control panel – siren mode (JA-60 or 65) – while in the service

mode of the control panel, enter code 299.

5. Up to 8 doorbell buttons or detectors can be used with one UC-260.

6. Exit the programming mode by pressing the UC-260’s button

briefly.

If you enter the programming mode the way above, all enrolled

components will be erased from the memory.

Adding components

If you want to add additional doorbell buttons or detectors or if you

want to select another melody for an existing component, than:

1. Unplug the UC-260 from the outlet and wait for 5 seconds.

2. Plug it in again.

3. The button will light – press it and hold it down. After hearing a

short beep, release the button. The flashing button indicates it is

in the programming mode.

4. Enrolling new components (or selecting another melody):

• Doorbell button (RC-11, RC-22, RC-28) can be enrolled by

pressing a button on the controller. Multiple pressing of the

controller’s button will allow you to scroll to a desired melody.

• Detector - chime mode (JA-60 detectors) can be enrolled by

inserting batteries into a detector. If you remove the batteries and

insert them again you can scroll to a desired melody (wait for 10

seconds before reinsertion).

5. Control panel – siren mode (JA-60 or 65) – while in the service

mode of the control panel, enter code 299.Up to 8 doorbell buttons

or detectors can be used with one UC-260.

6. Exit the programming mode by pressing the UC-260 button briefly.

Deleting components

Press and hold a button on the UC-260 and plug the UC-260 into

the mains outlet. Two beeps can be heard and all components will be

erased.

Loudness selection

• The UC-260 must be in its operating mode (plugged in).

• Press and hold the button down.

• After 2 sec you will hear a melody with the new loudness selected

• Release the button.

This way you can toggle between a standard and a quieter one.

This setting doesn’t affect the alarm siren sound.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron UC-260 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info