Bedienungsanleitung Jablotron UC-281 (Seite 2 von 2) (Englisch)

555023

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Setting buttons:

LEARN if this button is briefly pressed, you can scroll through the

learning modes of Z1-Z8 zones (a selected channel is

indicated by a red flashing LED).

RESET if this button is briefly pressed, the learning mode of a

selected zone will be closed. When this button is pressed for

more than 3 sec., a selected zone will be deleted (confirmed

by flashing of the TMP, BAT and TRB indicators). When this

button is pressed for more than 6 sec., all zones will be

deleted (confirmed by flashing of all indicators). Note, in

order to delete all zones, a learning mode of any zone must

be selected first.

UC-281 wireless interface 2 / 2 MFT51704

Jumpers:

1s / 3s pulse length of 1 sec. or 3 sec. of Z1-Z8 output relays

NO / NC normally closed or normally opened mode of Z1-Z8 output

relays (TMP, BAT and TRB are normally closed)

Supervision - Regular checking of wireless detectors’ communication

can be disabled (NO SUPERVISION position). This setting

is recommended in places with radio interferences. When

the supervision is enabled, lost communication will trigger

the TRB output relay.

Indicators:

POWER The green LED indicates the presence of the power supply

Z1 - Z8 LED lights green when zone is occupied;

LED lights red when zone detector is triggered;

LED flashes red, when zone is in a learning mode;

LED flashes red together with the TMP, BAT or TRB LED =

tamper, low battery or trouble signal in zone

TMP tamper alarm – flashes together with a corresponding zone

indicator every 3 sec.

BAT low battery - flashes together with a corresponding zone

indicator every 3 sec.

TRB trouble or lost communication - flashes together with a

corresponding zone or SIR indicator every 3 sec.

Enrolling of wireless components

Enrolling of detectors

• Scroll to a desired zone Z1-Z8 using the LEARN button

• JA-60 detectors will be enrolled by inserting their batteries or

switching on a power supply

• Successful learning is indicated by the red LED

• If you enroll a component to a new zone, it will move from its

previous position

• Only one detector can be enrolled to each zone

Enrolling of remote controls

• Scroll to a desired zone Z1-Z8 using the LEARN button

• RC-xx remote controls will be enrolled by pressing a button (while in

pulse mode). Button A, B or double press can be enrolled.

• RC-11 or RC-22 Remote controls can be enrolled to any zone in an

ON/OFF mode by pressing both buttons and keeping them pressed

for more then 5 sec. After this the corresponding relay will switch on

when the A button is pressed, and off, when the B button is pressed.

• If a combination of double press and ON/OFF mode is required, the

ON/OFF mode must be enrolled first.

• Successful learning is indicated by the red LED

• If you enroll a remote control to a new zone, it will move from its

previous position

• Only one remote control can be enrolled to each zone

Erasing components

If you want to delete any item from a UC-281, use the RESET button

(the procedure is described in “Setting buttons” paragraph).

Extension for more zones

When 8 zones are not enough, you can use UC-282 expander

modules. Each UC-282 module provides additional 8 zones.

A maximum of 4 expanders can be used with UC-281. Modules are

interconnected using the IN and OUT connectors, wiring should not

exceed 1 meter. Each UC-282 must be powered by 12 V DC

separately.

If communication with wireless modules UC-216, UC-222 or JA-60A

wireless siren is required, use the UC-280 interface module.

Internet: www.jablotron.cz

Tel.: +420 483 559 999

fax: +420 483 559 993

Pod Skalkou 33

466 01 Jablonec nad Nisou

Czech Republic

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron UC-281 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info