Bedienungsanleitung Jablotron UC-6007 (Seite 1 von 2) (Englisch)

554920

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

UC-6007/6014 receiver 1/2 MJQ51102

The UC-6007/6014 receiver

The UC-6007 is a 7-channel receiver of signals from TP wireless

thermostats or from JA-60 wireless detectors (JA-60N, JA-60SP, JA-

60SR, JA-60G etc.) and RC-4x remote controls. The receiver has 7

outputs, which can be used to control various devices. LEDs on the

receiver’s front cover indicate the status of each output channel.

The UC-6014 is 14 channel version. Due to maximal current limits

load the pulse switching of the outputs is used. Therefore the UC-6014

should be used only with thermostatic regulators. It should not be used

to control any relay semiconductor switch etc.

When used with wireless thermostats, the UC-6007/6014 can

efficiently control multi-zone heating and cooling systems. Additionally,

a power relay is used as a pump control (the relay is on if any output is

triggered).

Installation

Attach the unit to the desired location with three screws. Route all the

cables to the unit before you tighten the case.

Fix the cables firmly inside the box by a sliding strap.

Note: Only a qualified technician can provide installation and

servicing. The user is not allowed to open the cover and/or make

any modifications.

Terminal description:

AC, AC – power input 24 V AC

L_A, N_A,

PE_A – power supply input for the circulatory pump (use an

external fuse for its protection)

L_B, N_B,

PE_B – terminals for the circulatory pump connection (the L-B

terminal is triggered if any of the 1-7(14) outputs are

switched on)

1- 7 – transistor outputs (switchable to ground)

COM – common positive output terminals (24V DC)

The receiver is protected against shorts on the output. If the output is

overloaded (the current is greater than 0.4A), then the output is

automatically disconnected. A fault is indicated by rapid red flashing of

the corresponding LED indicator. The output is under constant

monitoring and when the output current decreases below 0.4A the

output will be switched on again.

If it is necessary to have more channels, then it is possible to

connect another unit via a 2-wire cable. The S/M (slave/master) jumper

determinates the main receiver. If only one receiver is used, then the

jumper must remain in the master position.

Enrollment of transmitters

For each channel of the receiver, a transmitter (thermostat or

wireless detector) can be enrolled in the following way:

• Repeatedly press button

< or > (left, right arrow) to select the

desired channel (the current channel will be indicated by its LED

flashing)

• Insert batteries into the transmitter (thermostat or detector). When

powered up, the transmitter generates an enrollment signal and its

code is stored in the selected receiver channel’s memory

• Enrollment of the transmitter is confirmed by the constant lighting of

the green LED

Only one transmitter can be enrolled to each channel. A transmitter

can be enrolled to multiple channels or other receivers without any

restrictions. If you try to enroll a new transmitter to an occupied channel,

the new transmitter will be stored and the former one will be deleted.

Deleting a transmitter

To delete an existing transmitter:

• Using buttons

< and > select the desired channel (the current

channel will be indicated by its LED flashing)

• Press the RES button, the corresponding LED will turn off and the

transmitter is deleted.

Power input 24V AC

Fuse 3.15A

Jumper slave/master

Outputs 1-7(14)

Power supply

Circulatory pump

relay board

Fuse T 200mA

Terminal digital bus for

connection another

UC-6007(14) unit

Indicators 1-7 (1-14)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron UC-6007 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info