Bedienungsanleitung Jacob Jensen Smoke Alarm Optical JBXS03 (Seite 17 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch)

652552

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Alarm and volume

The alarm is activated when there is smoke in the detector. The alarm signal is

approximately 85dB/3m. The alarm signal is active as long as there is smoke in

the detector. When there is no longer smoke in the detector, the smoke alarm

will revert to stand-by / normal operation automatically.

Alarm signals

Acoustic signal

One short beep app. every minute indicates that the battery is weak and must

be replaced.

Two short beeps indicate malfunction due to background light or outer

interruptions of the smoke chamber.

Three short beeps indicate technical malfunctions.

Four short beeps indicate that the smoke alarm is dirty and must be cleaned.

A continuous sound indicates that there is smoke in the detector.

Visual signal

One flash every eighth seconds indicates normal operation.

Two flashes every eighth seconds indicate reduced sensitivity (pause function).

A continuous flash indicates smoke detection.

How to stop the alarm

One short beep app. every minute:

Replace the battery. (See further under "Replacement of battery”).

Two short beeps:

Remove the background light or outer interruptions which causes the

disturbance of the smoke alarms operation.

Three short beeps:

The smoke alarm needs to be tested.

Note: Modifying or tampering with the internal components of the smoke

alarm may cause malfunction and will invalidate the warranty.

Four short beeps:

Clean the smoke alarm. (See further under "Maintenance").

Continuous signals (both visual and acoustic):

Alarm for smoke detection / fire.

(The alarm will sound as long as there is smoke in the detector.

The alarm can be stopped by pressing the red test button.)

Mounting

The smoke alarm should be fitted using the enclosed

mounting bracket, which is to be mounted in the

ceiling with one screw only (screw and plug for 5 mm

drill enclosed – please use a special plug for plaster

ceilings).

When the bracket is fixed, the smoke alarm is attached with a click. It is now firm

but can be turned for adjustment around the point to which it is attached.

Replacement of battery

The mounting plate makes it easy to pull down the smoke alarm for cleaning and

for replacement of the battery. As an extra safety precaution, the smoke alarm

cannot be mounted without a battery. The smoke alarm requires one 9 VDC

battery, (included – mounted in the battery-compartment).

Please note: The smoke alarm normally operates up to 10 days from the first

indication of low battery.

Please note: At first time installation simply remove the plastic strip between the

terminals and the contact before mounting the smoke alarm.

Note: For optimal detection the smoke alarm should be installed in a suitable

location as described above.

After mounting and after every battery change, test the smoke alarm by pressing

the red test button until a penetrating, clear signal is heard. Make sure that

the red test button flashes every eighth second. When the alarm is set-off, a

penetrating, rapidly pulsating signal is given out (min. 85dB/3m). The alarm can

be stopped by pressing the red test button.

Maintenance

The following guidelines will help you care for the JACOB

JENSEN

Smoke Alarm

so you can enjoy using it for many years.

1. Keep the smoke alarm dry at all times. If it becomes wet, wipe it dry

immediately and remove the batteries. Liquids can contain minerals that might

corrode the electric circuits.

2. Use and store the smoke alarm only under normal temperature. Temperature

extremes can shorten the life of electronic components, damage the battery

and distort or melt plastic parts.

3. Handle the smoke alarm gently and with care. If it is dropped, circuit boards

can be damaged, resulting in malfunction.

4. Keep the smoke alarm free from dust and dirt to avoid the premature wear of

parts.

5. Clean the smoke alarm by wiping with a soft cloth. Do not use aggressive

chemicals, cleaning solvents or strong detergents.

6. Use only fresh batteries of the required size and type. We recommend Alkaline/

Top Grade batteries only. Always remove old or weak batteries as they might

leak chemicals that will destroy the smoke alarm.

7. Modifying or tampering with the internal components of the smoke alarm may

cause malfunction and will invalidate the warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jacob Jensen Smoke Alarm Optical JBXS03 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info