Bedienungsanleitung Jamo J 112 SUB (Seite 5 von 31) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

616034

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

CONNECTIONS AND CONTROLS

CAUTION: Ensure that the subwoofer is unplugged from the AC wall outlet before making

any connections.

“LINE IN” Connection - Most of today’s surround receivers (and pre-ampliers) have a line

level subwoofer output labeled Subwoofer Pre Out, Sub Out, SW Out, etc. If you have this

output, connect one end of a subwoofer cable to it and connect the other end of the cable

into the subwoofer line input labeled LEFT/LFE. This connection allows the subwoofer to

operate with both music and surround sound movies (refer to your receiver manual). In

absence of a subwoofer output on your receiver, as an alternative hookup, you can connect

Left and Right channel Pre-Amp Outputs from your receiver (if provided) to the Left/LFE

and Right input on the subwoofer.

WA-2 Port Connection - For wireless connectivity of your new Jamo J 110 SUB or

J 112 SUB , the optional WA-2 is available. The WA-2 will only operate with select Klipsch,

Energy, Mirage and Jamo brand subwoofers that have a “WA Port” input. The WA-2 is a 2.4

GHz product designed to wirelessly transmit a signal up to a 50 foot radius. See klipsch.com

for more details.

Level

- If your subwoofer is connected to a Subwoofer Output of a surround receiver, rst

set the subwoofer volume level control in the receiver to the “half way” or “0 dB” position.

Then increase the volume (or gain) of the subwoofer up until the subwoofer’s volume level

matches the output of your main speakers. After this setup is completed, the volume control

on your system’s main amplier or pre-amplier will be the volume control for both your

subwoofer and speakers together. If your subwoofer is connected to the L/R Pre-Amp Outputs

of a receiver there will be no subwoofer volume in that receiver to set before setting the

subwoofer’s gain control.

“LOWPASS” Control - The crossover point chosen determines where low bass frequencies

are “handed o” from the speakers to the subwoofer. If setting the crossover point in the

receiver, turn the Lowpass Filter knob on the subwoofer to the farthest point right (160Hz).

Set the crossover point based on the size of the main left/right speakers you are using in

the system. As a general rule, for larger, oorstanding speakers, set the crossover point

between 50Hz-90Hz. If using small bookshelf or “satellite” speakers for the mains, set the

crossover point between 90Hz-150Hz. The smaller the speaker, the higher the setting

until the bass frequencies blend well between the speakers and your subwoofer once your

system is completely hooked up. If your receiver does not have a crossover point setting, set

the Lowpass Filter on the subwoofer instead within the same recommended settings (see

receiver manual for additional speaker setup info).

“PHASE” 0/180 - This control is used to acoustically match the subwoofer’s output to your

main speakers. Select the position, either 0° or 180°, in which your subwoofer has more

output at the listening position.

“POWER” AUTO/ON/OFF - When this switch is in the “ON/AUTO/STANDBY” position, the

subwoofer will automatically turn “on” when it senses a signal. It will automatically go into

“standby mode” after 15-20 minutes with no signal. When this switch is in the “OFF” position,

the subwoofer will remain “o” until the switch is manually turned back to the “ON/AUTO/

STANDBY” position.

Power LED indicator - Located on the front bae, this LED indicates the operating status

of the built-in amplier. The LED will light green when the amplier is on and receiving

a signal. If the LED is dark and not lit, the amplier is o. For more information on the

controls mentioned in this manual and on bass management, see your dealer or visit

www.jamo.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jamo J 112 SUB Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info