Bedienungsanleitung JBL Array series (Seite 6 von 12) (Englisch)

809516

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

1400 ARRAY ASSEMBLY

Due to the weight of the

1400 Array horn module, it

is packed separately from

the low-frequency enclosure.

It is a very simple procedure

to install the module, and the

necessary instructions are

listed below. The required

Allen-tipped screw driver is

included in the accessory

pack.

1. Carefully remove the horn

module from the packaging

and place it face down on a

soft surface.

2. Locate the cardboard

accessory sleeve and

remove the hardware.

3. The accessory sleeve

should contain:

a. 2 Long 1/4" x 20 Allen-

head bolts

b. 1Short 1/4" x 20 Allen-

head bolt

c. 1 Logo plate

d. 1 Rubber hole plug

e. 4Metal coasters

(to protect wood and tile

floors from the spike feet)

4. Carefully unpack the low-

frequency enclosure and

place it upright. It would be

helpful to position it near its

final position in the room

since it is much easier to

move without the additional

weight of the horn module.

5. Notice the two threaded

inserts on the angled face

of the top and also the small

L-bracket on the top. These

are the attachment points

for the horn module. Imme-

diately adjacent to the L-

bracket is a recessed con-

nector which will make the

electrical connection for the

horn module.

6. Although the module can

be installed by one person,

it is easier if a second set

of hands are available.

7. Cradle the horn module with

the opening along your fore-

arm and, using your free

hand, connect the plug

coming from the bottom of

the horn assembly into the

jack on the top of the

enclosure.

8. You can now place the horn

in position on top of the

enclosure. The L-bracket

fits in an opening under the

horn assembly. The module

will sit on top of the enclo-

sure by itself, although it

should always be steadied

until fully mounted.

9. Line up the two mounting

holes on the lower lip of the

front of the horn with those

in the enclosure. Partially

install one long bolt and

then the other one. It may

be necessary to lift the horn

slightly so that the bolts

install smoothly. Do not

force or cross-thread them.

10. Once both bolts have been

started, work them in all of

the way, but do not tighten

them securely just yet.

11. Install the remaining short

bolt in the hole at the

bottom rear of the horn

module. You can fully

tighten this bolt.

12. Now completely tighten the

two front bolts.

13. Everything should be tight

and properly aligned at this

time. If not, loosen, realign,

and retighten as required.

14. The final steps are to

remove the backing from

the logo badge and place it

in the recess on the lower

horn lip, and to use the

rubber hole plug to hide the

hole at the bottom rear of

the horn module. Do not

complete these steps until

the system has been turned

on and tested acoustically.

Make sure the horn module

is playing first. Once the

logo badge and rubber

plug hole are installed, it

is extremely difficult to

remove them.

Project Array OM 1/10/06 12:21 PM Page 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL Array series Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info