Bedienungsanleitung JBL Control NOW AW (Seite 4 von 30) (Englisch)

507345

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

WALL SURFACE-MOUNTING

When deciding upon a location for the JBL Control NOW speaker, take care

NOT to install the mounting bracket closer than 3" (7,6 cm) (horizontal) and 8-1/2"

(21,5 cm) (vertical) to the ceiling. Any closer than the minimum measurements

will not allow the room needed to position and slide the JBL Control NOW

speaker into the mounting bracket.

CAUTION

The customer is responsible for proper selection and use of mounting hardware

(available through hardware stores), to properly and safely wall-mount the

speakers. The JBL Control NOW speaker was designed to be easily installed.

However, if you are unable to clearly and fully understand and follow the

instructions in this manual, or if you are unsure of your ability to properly install

these loudspeakers, please contact your dealer or a qualiﬁ ed installer. Please

do not use any power tools during installation. Power tools can exert excessive

and unnecessary torque which, in turn, can damage fasteners or other parts

and accessories, reducing their strength and causing possible failure of the

fastener or part. A failed or damaged fastener or part may not be able to

perform as designed, and may lead to an unsafe installation.

1. Run the wiring to the location desired for mounting the JBL Control NOW speaker.

2. Using a level, secure the mounting bracket to the wall. Be sure to use an

appropriate anchor.

Corner/Wall-Mount-

Bracket Assembly

NOTE: There are two

cable access holes

provided in the Wall-

Mount Assembly.

Appropriate

anchors

3"(7,6 cm) Minimum

distance from ceiling

to top of bracket

(horizontal mount)

8-1/2"(21,5 cm) Minimum

distance from ceiling

to top of bracket

(vertical mount)

3. Connect the wires to the JBL Control NOW speaker.

IMPORTANT: Make sure all equipment is turned off before making

any connections. For speaker connections, use a high-quality speaker wire

with polarity coding. The side of the wire with a ridge or other coding is

usually considered positive polarity (i.e., +).

NOTE: If desired, consult your local JBL dealer about speaker wire and

connection options.

RED = +

BLACK = —

1. Strip 1/4" (6 mm) of wire

2. Press and push connector

3. Insert bare end;

release push connector

The speakers have coded terminals that

accept a variety of wire connectors. The most

common connection is shown in the diagram

to the left. To ensure proper polarity, connect

each + terminal on the back of the ampliﬁ er

or receiver to the respective + (red) terminal

on each speaker, as shown. Connect the

– (black) terminals in a similar way. See

the owner’s guides that were included with

your ampliﬁ er, receiver and television to

conﬁ rm connection procedures.

IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making

connections. Doing so will cause poor imaging and diminished bass response.

RED = +

BLACK = —

Standard

Connection

Wiring diagram shows

polarity connections for

one channel of a stereo or

home theater system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL Control NOW AW Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JBL Control NOW AW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info