Bedienungsanleitung JBL Control NOW (Seite 11 von 30) (Englisch)

507344

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

English

5. The mounting bracket is designed to trap the ﬂ ange of the JBL Control NOW

speaker by securing the mounting-bracket cap with two screws through the

bottom of the mounting bracket. Run the loose end of the multiunit wiring

adapter through the rear cable-management hole in the mounting bracket,

and rest the JBL Control NOW speaker’s rear ﬂ ange in the mounting bracket,

as shown. This will support the weight of the speaker. Now slide the mounting-

bracket cap over the assembly. Secure the mounting-bracket cap by

inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the

mounting bracket and tightening.

Mounting-Bracket Cap

Mounting Bracket

#10-32 x 2" (M5 51 mm) Screws (2)

(side view)

6. Place the large end of the multiunit wiring adapter into the second speaker

to be installed. Slide the multiunit wiring adapter into the rear of the speaker

at a slight angle and rotate clockwise.

Already connected to the other speaker.

7. Connect the terminal assembly to the back of the multiunit wiring adapter.

It will snap securely into place.

Already connected to the other speaker.

8. Now connect the wires to the terminal assembly.

IMPORTANT: Make sure all equipment is turned off before making

any connections. For speaker connections, use a high-quality speaker wire

with polarity coding. The side of the wire with a ridge or other coding is

usually considered positive polarity (i.e., +).

NOTE: If desired, consult your local JBL dealer about speaker wire and

connection options.

RED = +

BLACK = —

1. Strip 1/4" (6 mm) of wire

2. Press and push connector

3. Insert bare end;

release push connector

The speakers have coded terminals that

accept a variety of wire connectors. The most

common connection is shown in the diagram

to the left. To ensure proper polarity, connect

each + terminal on the back of the ampliﬁ er

or receiver to the respective + (red) terminal

on each speaker, as shown. Connect the

– (black) terminals in a similar way. See

the owner’s guides that were included with

your ampliﬁ er, receiver and television to

conﬁ rm connection procedures.

IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making

connections. Doing so will cause poor imaging and diminished bass response.

RED = +

BLACK = —

Standard

Connection

Wiring diagram shows

polarity connections for

one channel of a stereo or

home theater system.

9. To orient the JBL logo into the correct position, pull the JBL logo slightly

outward from the speaker grille and rotate. The JBL logo is held in place by

a spring. Peel the adhesive cover off the mounting-bracket covers and

attach to the top and bottom of the mounting assembly.

Mounting-Bracket

Covers

Mounting-Bracket

Covers

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL Control NOW Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JBL Control NOW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info