Bedienungsanleitung JBL GTO 3501 (Seite 5 von 15) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Finnisch)

67984

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Installation Warnings and Tips:

• Disconnect the negative (–) lead from your vehicle’s

battery.

• At the installation sites, locate and make a note of all

fuel lines, hydraulic brake lines, vacuum lines and

electrical wiring. Use extreme caution when cutting

or drilling in and around these areas.

• Choose a safe mounting location away from

moisture.

• Make sure there is sufficient air circulation at the

mounting location for the amplifier to cool itself.

• Mount the amplifier, using the supplied hardware.

Specifications

• 225W RMS x 1 channel @ 4 ohms and ≤1% THD + N*

• 360W RMS x 1 channel @ 2 ohms and ≤1% THD + N*

• THD + N: 0.04% (rated power @ 4 ohms)

• Signal-to-noise ratio: 85dB

(reference 1W into 4 ohms)*

• Signal-to-noise ratio: 104dB

(reference rated power into 4 ohms)

• Frequency response: 20Hz – 330Hz (–3dB)

• Max power: 360 watts

* CEA-2006A-compliant

Speaker Output Connectors

• Connect the subwoofer to these terminals,

observing proper polarity. Either + or –

terminal may be used. Minimum total

impedance is 2 ohms.

Fuses

• Replace only with the same type and rating.

Power Input Connectors

• +12V: Connect to the positive terminal of the

vehicle’s battery. 8 AWG wire is recommended.

Install an appropriate fuse holder and fuse (60A

minimum) within 18 inches of the battery. Make

sure the wire is not damaged or pinched during

installation. Install protective grommets when

routing wires through the firewall or other sheet

metal.

• GND: Connect to the vehicle’s chassis. Refer to

the picture below.

• REM: Connect to the “Remote Out” lead from the

source unit or to a source of switched

12V+ (ACC).

Aux Output Connectors (RCA)

• Nonfiltered pass-through output. Connect to the

input of an additional amplifier.

Input Connectors (RCA)

• Connect to the RCA outputs from the source unit

or signal processor.

Input-Level Control

• Used to match the input level of the amplifier

to the output level of the source unit.

• See

for the adjustment procedure.

Low-Pass Filter Frequency Control

• 12dB/octave low-pass filter,

variable from 32Hz to 320Hz.

• See

for the adjustment procedure.

DBO (Dynamic Bass Optimization) Variable

Subsonic High-Pass Filter With Variable Boost (Q)

• For woofers in tuned (vented) enclosures, set the

Frequency control to a value 10Hz below the

enclosure’s resonance (tuned) frequency.

• For woofers in sealed boxes, set the control to

any value you prefer between 30Hz and 50Hz.

• Set the Boost control according to your

preference, being careful not to apply

enough boost to damage your woofer(s).

A DBO High-Pass Filter Frequency control,

variable between 20Hz and 100Hz. See above

for appropriate settings.

B DBO Boost control provides up to

12dB of boost slightly above the high-

pass filter’s frequency. See above for

appropriate settings.

Optional Remote Level Control (RLC) Connector

• Connect the Remote Level Control (RLC) here,

using the RJ-11 cable

(supplied with the RLC).

Power On LED

• Illuminated when the amplifier is on.

Protect LED

• Illuminated under any of the following fault

conditions: battery over/under voltage, short

circuit in speaker wires, amplifier is too hot,

amplifier’s output circuit has failed (DC voltage is

present in the amplifier’s output).

Setting Input Level

A Turn Input Level control counterclockwise to

6V (minimum).

B With a dynamic music track playing, turn the

head unit’s volume control to the 3/4 position.

C Turn Input Level control clockwise until the

bass output is proportionate to the output of

the high-frequency speakers, according to

your preference.

D Input level is now adjusted correctly.

Setting the Crossover

A Crossover setting for subwoofers.

Note: Acceptable frequency ranges are indicated

in gray.

The Remote Level Control, if installed, will allow

you to adjust the level of bass while seated in the

listening position.

Factory Bolt Ring Connector

Ground Wire

Note: Remove any paint

below ring connector.

Star Washer

GTO3501 CAR AUDIO SUBWOOFER AMPLIFIER OWNER’S MANUAL

This product is designed for mobile applications and is not

intended for connection to the mains.

A valid serial number is required for warranty coverage.

Features, specifications and appearance are subject to change

without notice.

ENGLISH

0158CSK - JBL GTO3501 OM.qxp:34297_GTO3501_OM.qxd 13/08/09 15:37 Side 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL GTO 3501 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info