Bedienungsanleitung JBL mr 28 (Seite 3 von 8) (Englisch)

415145

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

them, at the listening position, is

between 40 and 60 degrees. For

example, if your listening position is

8 to 12 feet (2.5m to 4m) from each

speaker, the two systems should be

about 8 feet (2.5m) apart.

Center Channel Model: As the

center channel contains the dialog

and other central action sounds, the

speaker should be located very close

to the Monitor/TV and centered with

the Monitor/TV’s center line. Place

the MR Center directly on top of or

directly below the Monitor/TV with the

front edge of the speaker grille flush

with the edge of the Monitor/TV. You

should have your Left and Right

speakers within a 2 ft or less height

range of your Center Channel for

proper sonic performance (see Fig 2).

In Case Color Interference Occurs:

The speaker is shielded to work with

video applications, however some

color interference may be observed

on the TV screen depending on the

type of your TV set. If color interfer-

ence is observed, turn your TV off for

15 minutes and move the speaker

back about 1" from the front edge of

the TV. Turn on TV and recheck. If

this is not far enough, move back fur-

ther and experiment until the interfer-

ence disappears. You may have to

turn the TV off for a few minutes and

turn it on again to clear the screen.

CONNECTIONS

To connect the loudspeaker systems

to the receiver or amplifier, use two-

conductor insulated wire. Your JBL

dealer can recommend suitable

cables, or you can buy wire at most

hardware or electronic stores. We

recommend #16 AWG wire as a mini-

mum size. If your speaker is more

than 30 feet (10m) from your receiver

or amplifier, use larger diameter

lower gauge wire. Connections are

made at the terminals located on the

back of the MR Series speakers.

Preparing the Hookup Wire

Carefully plan your wire lengths

before cutting any speaker wire.

Be sure to allow plenty of extra

wire to help hide paths in corners,

along baseboards, etc.

1. For Left and Right Speakers, first

determine the wire length needed

between the most distant speaker

and the receiver or amplifier.

2. Now make the hookup wires for

both speakers this length, even if one

loudspeaker is much closer to your

amplifier than the other. This will

help maintain proper signal balance.

(For the MR Center, determine the

length needed from AV receiver’s

center channel output to speaker).

3. Strip off

⁄8" of insulation from both

ends of each conductor.

4. Twist each set of thin wires into a

tightly-bunched spiral.

5. At this point you need to identify a

visual difference between the two

conductors of each molded pair of

speaker wire. Differentiating marks

can be a different color wire (copper

or “silver”); a strand of yarn in one

conductor; thin, raised ribs on one

MR SERIES LOUDSPEAKERS

(2 ft. or less)

Fig. 2

MR Series OM 7/28/98 10:32 AM Page 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL mr 28 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info