Bedienungsanleitung JBL On Air Control 2.4G (Seite 6 von 12) (Englisch)

809363

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Some computer sound cards feature preamp outputs in addition to or instead

of speaker outputs. If your computer does feature preamp outputs, we

recommend that they be used instead of speaker outputs. If you would like to

connect the computer to the JBL On Air Control 2.4G using preamp outputs on

your computer, follow the steps in Connection A.

Connection Option A

Connecting using the preamp outputs on your source:

NOTE: Make sure power is turned off on all components.

Step 1.

Connect the interconnect cable (included) to the left and right front/main

preamp outputs or zone 2 outputs or REC outputs and the inputs on the

transmitter module D,as shown in Figure 4.

Step 2.

Place the active speaker in the desired location in your home near an AC

outlet, as it needs to plug in to the wall.

Step 3.

Connect the speaker wire (included) to the push terminals on the active

speaker 5and the push terminals on the rear of the passive speaker 9,

as shown in Figure 3. Please note that the speaker wire supplied features a

polarity stripe to help distinguish its two conductors. Use this polarity stripe to

ensure that you are connecting the positive (+) terminal on one speaker to the

positive (+) terminal on the other, and the negative (–) to the negative (–). It

does not matter whether you use the striped conductor for connecting the

positive (+) terminals or the negative (–) terminals.

Step 4.

Plug the transmitter module Band active speaker 6into the wall outlet,

using the correct power supply and power cord. Make sure the transmitter’s

antenna Ais extended upwards.

Step 5.

Make sure the ID code setting on the transmitter Cis set to the same setting as

that on the active speaker 4.See page 8 of this manual for more information on

ID codes. If necessary,configure your receiver to activate the preamp level out-

puts for the main/front channels (consult your source’s owner’smanual for spe-

cific instructions).

Figure 4.

INPUT

CODE

1234

SOURCE

Front/Main/Second Room

Preamp Outputs

Step 3.

Connect the speaker wire (included) to the push terminals on the active

speaker 5and the push terminals on the rear of the passive speaker 9.

See Figure 3. Please note that the speaker wire supplied features a polarity

stripe to help distinguish its two conductors. Use this polarity stripe to ensure

that you are connecting the positive (+) terminal on one speaker to the positive

(+) terminal on the other, and the negative (–) to the negative (–). It does not

matter whether you use the striped conductor for connecting the positive (+)

terminals or the negative (–) terminals.

Step 4.

Plug the transmitter module Band active speaker 6into the wall outlet,

using the correct power supply and power cord. Make sure the transmitter’s

antenna Ais extended upwards.

Step 5.

If necessary, configure your source to activate the preamp level outputs for

the surround/rear channels (consult your source’s owner’s manual for

specific instructions).

Make sure the ID code setting on the transmitter Cis set to the same setting

as that on the active speaker 4.See page 8 of this manual for more information

on ID codes. When connected properly, the top LED on the front of the active

speaker should be green. When first plugged in, it will sometimes take several

seconds for the Control 2.4G active speaker to initialize and “wake up.“ Until

then, the top LED will be in red. Once the top LED is green, the bottom LED should

flash green until the transmitter and active speaker “lock in.” It will then also

light in solid green. This LED will light in orange if the local input on the active

speaker is selected (see page 8 under Local Input for more details).

Application 2

Adding speakers to remote locations around your home:

Audio sources that can be used in this application may be an A/V receiver or

audio receiver, a portable audio player, or a computer featuring a sound card.

First, determine whether your source contains RCA-type preamp outputs for

the front/main channels or a 1/8-inch stereo single-pin output. On an A/V or

audio receiver,the preamp outputs are usually indicated by RCA-type jacks on

the back of the receiver labeled as “pre-out” (please refer to your source’s

owner’s manual to confirm whether it includes preamp outputs). If your source

includes these RCA-type outputs, follow the steps in Connection Option A.

If your source features a 1/8-inch single-pin stereo jack, follow steps in

Connection Option B. If your receiver does not feature either type of preamp

outputs for the front/main channels, it cannot be used with Control 2.4G. Some

computer sound cards feature more than one 1/8-inch single-pin jack. There

is almost always one output that is called a speaker output. However, some

sound cards feature a preamp output or line output in addition to or instead

of speaker outputs. If your computer does feature preamp or line outputs, we

recommend that they be used instead of speaker outputs.

Figure 3.

CODE

1234

DC 20V SUB OUT LINE IN

LEFT CHANNEL SPEAKER

TORIGHT SPEAKER

–

RIGHTCHANNELSPEAKER

TOLEFT SPEAKER

–

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL On Air Control 2.4G Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JBL On Air Control 2.4G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info