Bedienungsanleitung JBL On Air Control 2.4G (Seite 9 von 12) (Englisch)

809363

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Adjustable wall brackets are included for the two speakers and transmitter

module. The included brackets are for wall-mounting only. It is not to be used

for ceiling mounting. Ceiling mounting of the Control 2.4G transmitter and/or

speakers is not recommended, regardless of bracket used.

Wall-Mounting the Speakers

Using Wall Brackets Provided

Important Safety Note: Proper selection of mounting hardware not included

herein, and proper assembly and installation of brackets, including, but not

limited to, selection of appropriate weight-bearing support and bracket use

with the specified speaker only is the exclusive responsibility of the customer.

Manufacturer disclaims any liability for the selection of mounting hardware

and/or bracket installation.

A. Loosen and remove the molded nut

(2)

by turning it counterclockwise. Use

the supplied metal bar (5) if necessary by inserting it in one of the holes on

the molded nut

(2)

B. Pull the ball/shaft

(3)

out of the wall bracket

(4)

C. Slide the molded nut

(2)

onto the ball/shaft

(3)

with threaded opening facing

the ball, and thread on the metal nut

(1)

all the way onto the ball/shaft

(3)

with the nut’s (1) ”knurled” surface facing away from the ball.

D. Screw the ball/shaft (3) into the threaded 1/4"-20 insert on the back of the

speaker cabinet

(6)

until it is fully seated against the bottom of the insert.

Back out the ball-shaft assembly 1/2 of a turn and tighten the nut against the

speaker. If the ball and shaft assembly is not backed out before tightening

the nut, performing Step G below may dislodge the threaded insert in the

speaker housing and permanently damage the speaker.

E. Tighten the ”knurled” nut (1) using a crescent wrench until it is firmly seated

against the back of the speaker and has fully locked the ball/shaft

(3)

and the

speaker cabinet together. Please note that once this nut is tightened, it may

embed some marks on the back of the speaker where the attachment is

made. However, these marks will be covered by the nut (1).

F. The backup cord

(8) is

provided as an additional measure to prevent the fall

of the speaker in case the speaker becomes detached from the wall bracket.

One of the two lower screws

(9)

that attach the wall bracket

(4)

to the wall will

need to go through the eyelet

(11)

at the end of the cord before going through

the wall-bracket hole. Mount the wall bracket

(4)

onto a wood stud on the wall,

using #10, minimum 1-inch-long, panhead wood screws. Make sure that all four

screws are driven into the stud, not drywall. If the bracket needs

to be mounted on drywall, the use of properly selected and installed wall

anchors and screws is essential. Make sure that the screw head is at least

0.36 of an inch (approximately 3/8 of an inch) or larger in diameter so that it can

properly hold the backup cord eyelet

(11)

G. Holding the speaker cabinet

(7)

with both hands, reinsert the ball portion of

the ball/shaft

(3)

into the wall bracket

(4)

H. Hand-tighten the molded nut

(2)

while positioning the speaker for the intended

orientation.

I. Once the orientation of the speaker is finalized, use the metal bar (5) in one

of the holes on the molded nut

(2)

and tighten securely.

J. Securely attach the other end

(10)

of the backup cord

(8)

to the Control 2.4G

by engaging it through the bar (12) on the back speaker.

Also included with the system is a wall-mount holder for the active speaker’s

power supply. If desired, you may attach this holder to the wall and insert the

speaker’s power supply.

WALL AND STAND PLACEMENT

TO LEFT SPEAKER

+–

TO LEFT SPEAKER

+–

CORRECT INCORRECT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL On Air Control 2.4G Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JBL On Air Control 2.4G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info