Bedienungsanleitung JBL Project Everest DD65000 (Seite 22 von 26) (Englisch)

793353

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

4342

BI-WIRE CONNECTION METHOD

IMPORTANT: When you use the bi-wire or bi-amp connection

method, remove the shorting straps from the terminals (referring

to the gures below) and re-tighten the knobs on the terminals. If

the ampliers are connected to the Project Everest loudspeakers

in the bi-wire or bi-amp mode with the shorting straps still on,

the amplier outputs will be shorted, which could result in costly

amplier damage when power is switched on.

The bi-wire connection method requires one amplier channel and

two sets of speaker wires for each loudspeaker. After removing

the shorting straps, you can make connections to the individual

network sections using all four connectors, with one set of wires

to the upper (high-frequency) terminals and another set of wires to

the lower (low-frequency) terminals.

BI-AMP CONNECTION METHOD

The bi-amp connection method requires two ampliers, one for

the low-frequency transducers and one for the high-frequency

transducers, and an external dividing network (electronic

crossover). After removing the shorting straps on the loudspeaker

connector panels, wires from the high-frequency amplier are

connected to the upper terminals, and wires from the low-

frequency ampliers are connected to the lower terminals.

Each of these connection methods described above has its own

advantages – your Project Everest loudspeaker system will deliver

superb performance with any of the methods described.

FINAL CHECKLIST:

• Connect all other system electronics and plug into AC

power outlets.

• Check all connections. In case of bi-amping or bi-wiring,

make sure both shorting straps are removed.

• Make sure the system orientation and HF/LF drive jumper

bars on the control panels are correctly set.

The loudspeakers are now ready for use. The Project Everest

loudspeaker system is fully functional as soon as it is set up. There

may be subtle tonal changes in bass output over the rst week to

10 days of operation. These are caused as the movement of the

low-frequency drivers becomes more uid and the parts settle in.

This process is completely normal and natural with transducers of

this caliber. Even during this initial period, there is no restriction on

the amount of amplication that may be applied. Enjoy!

Bi-Wire Connection Method

Note: Remove Shorting Straps

Receiver or

Amplier

(one channel

shown)

Speaker

Connector

Panel

Use Both Set

of Terminals

Shorting Straps

Removed

Bi-Amp Connection Method

Note: Remove Shorting Straps

INPUT

OUTPUT

HIGH-

FREQUENCY

OUTPUT

LOW-

FREQUENCY

OUTPUT

INPUT

Speaker

Connector Panel

High-Frequency

Amplier

(one channel shown)

Preamp/Processor

(one channel shown)

Electronic Crossover

(one channel shown)

Low-Frequency

Amplier

(one channel

shown) Shorting Straps

Removed

Use Both

Set of

Terminals

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL Project Everest DD65000 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info