Bedienungsanleitung JBL SA750 (Seite 17 von 22) (Englisch)

793371

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

EN-17

SETUP MENU

The setup menu allows you to configure various

aspects of the SA750 integrated amplifier.

Entering Setup Menu

To enter the setup menu, press the key on

the remote control.

Navigating The Setup Menu

The setup menu can be navigated by using the

remote control as shown below.

HOME Exit the menu and return to the home

display

UP Navigate to the previous menu option

DOWN Navigate to the next menu option

LEFT Navigate left or move to the previous

field

RIGHT Navigate right or move to the next

field

OK Save the current setting and move to

next option

BACK Save the current setting and exit

menu option

System Settings

Display

Allows the brightness of the front panel display to

be changed. The available settings are ,

and . The default setting is .

Dark Mode

Turns front panel display and status LED off.

Enable Input

Allows unused inputs to be removed from the

inputs accessed via the front panel control. Inputs

can still be selected via remote control using the

dedicated source keys.

Timeout

This option allows you to choose the length of

idle time before the unit goes into standby. The

available options are Off, 20, 30 minutes, 1, 2 and

4 hours. The default setting is 20 minutes.

System Code

Change the IR system code that the SA750

responds to (either 16 or 19). The default code is

16.

To Swap The Codes

Press and hold MODE and OK for 3 seconds.

The remote LED will flash. One flash means the

remote is now set to code 16. Two flashes means

the remote is now set to code 19.

Net Reset

Resets the network module to factory settings.

System Reset

Restores the SA750 to its factory default settings.

USB Update

Allows the SA750 to be updated via a USB stick.

Refer to the software release instruction for more

details available at www.JBL.com.

OTA UPG

If enabled the SA750 will update automatically if

left powered on overnight or in network standby.

If disabled software updates need to manually

installed. Refer to the software release instruction

for more details available at www.JBL.com.

System Info

Displays various system parameters including

MCU and Network software version numbers, IP

address, Friendly name, Googlecast name and

serial number.

Audio Settings

Dirac Curve

Specify which Dirac calibration is applied to each

input.

Note: When Dirac is run for the first time the curve will be

applied to all inputs.

Phones Ovr

Control whether or not the speaker outputs are

muted when a pair of headphones are connected

to the socket on the front panel. The

default is so the speakers and pre-outs will be

muted when headphones are connected.

PM Input

Specify which input is to be used in processor

mode. This mode can be assigned to most analog

inputs. In this case, the SA750 output level is set

to a fixed level. The default setting is .

Note: The PHONO input cannot be selected as the

processor input.

PM Volume

Specify the required volume level for the processor

mode input. The default is volume is 30.

Max On Vol

Limits the maximum volume when the SA750 is

switched on or comes out of Standby. The SA750

comes on at this stored volume setting if the last

used (possibly very loud) volume exceeds this

value. It is stored in memory and recalled each

time the unit is powered up.

Maximum Vol

Limits the maximum volume setting the SA750

can be turned up to for external inputs. This is a

useful feature to prevent accidental overdriving

of low power-handling speakers. It is stored

in memory and recalled each time the unit is

powered up.

Max Net Vol

Limits the maximum volume setting the SA750

can be turned up to for streamed content. This is

a useful feature to prevent accidental overdriving

of low power-handling speakers, or to prevent

volume being accidentally set to maximum

using streaming app volume sliders. It is stored

in memory and recalled each time the unit is

powered up.

Direct

Specify which analog inputs should operate in

direct mode.

Phono Input

Selects which Phono input is used, Moving

Magnet (MM) or Moving Coil (MC)

Filter

Specify which digital filter is used in the DAC.

Apodizing; Linear Phase Fast Roll Off; Linear

Phase Slow Roll Off; Minimum Phase Fast Roll

Off; Minimum Phase Slow Roll Off; Brick Wall or

Corrected Minimum Phase Fast Roll Off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL SA750 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JBL SA750

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info