Bedienungsanleitung JBL Studio SUB 260P (Seite 2 von 4) (Englisch)

648477

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

SUBWOOFER REAR-PANEL CONTROLS AND CONNECTIONS

1) Crossover Control: This control determines the highest frequency at

which the subwoofer reproduces sounds. The higher you set the Crossover

control, the higher in frequency the subwoofer will operate and the more its

bass will “overlap” that of the speakers. This adjustment helps achieve a

smooth transition of bass frequencies between the subwoofer and the

speakers for a variety of different rooms and subwoofer locations.

2) Phase Switch: This switch determines whether the subwoofer

transducer's piston-like action moves in and out in phase with the main

speakers. If the subwoofer were to play out of phase with the main

speakers, the sound waves from the main speakers could partially cancel

out the sound waves from the subwoofer, reducing bass performance and

sonic impact. This phenomenon depends in part on the placement of all the

speakers relative to the listening position and to each other in the room.

3) Bass Boost: When switched to 'On,' this boosts bass level for added

low-end power.

4) Power On Mode: When switched to 'Auto' position, the subwoofer will

then be in Standby mode. It will automatically turn 'On' when an audio signal

is detected at its inputs, and will return to the Standby mode when no audio

signal is detected by its inputs after approximately 10 minutes. Otherwise,

subwoofer will always remain powered until Power Switch is turned 'Off.'

5) Subwoofer Level: Use this control to adjust the subwoofer’s volume. Turn

the knob clockwise to increase the volume; turn the knob counterclock-wise

to decrease the volume.

6) On/Standby LED: When the Power switch is in the ‘On’ position, this

LED indicates whether the subwoofer is in the On or Standby state.

• When the LED glows green, the subwoofer is turned on.

• When the LED glows red, the subwoofer is in the Standby mode.

7) Line In/LFE Input Connectors:

• When you’re connecting the subwoofer to the dedicated subwoofer

output of a receiver/processor that has its own low-pass crossover

network, use the LFE Input connector.

• When you're connecting the subwoofer to the preamp or subwoofer

outputs of a receiver/processor that does not have its own low-pass

crossover network, use both Line In connectors and set the Input

Mode switch in the ‘Normal’ position. If your receiver/processor only

has one subwoofer output you can use either Line In connector.

8) Power Switch: Set this switch in the ‘On’ position to turn the

subwoofer on.

If you will be away from home, or will not be using the subwoofer for an

extended period, set this switch in the ‘Off’ position to conserve energy.

9) Power Cord: After you have made and veriﬁed the subwoofer’s input

connections, plug the power cord into an active, unswitched electrical outlet

for proper operation of the subwoofer.

DO NOT plug the power cord into the accessory outlets found on some

audio components.

POWER CORD

STUDIO

SUB 250P

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL Studio SUB 260P Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info