Bedienungsanleitung JBL TL260 (Seite 2 von 4) (Englisch)

507366

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

This TL260 features four rubber feet that enable it to be placed on

a smooth-surfaced floor, such as tile or hardwood. Four metal spikes

are supplied for use when the speaker is to be placed on a carpeted

surface to decouple the speaker from the floor. To insert the spikes,

gently lay the speaker on its side (not its front or back) on a soft,

nonabrasive surface. Each spike screws into the threaded insert in

the center of each rubber foot. Make sure all four spikes are

screwed in completely for stability.

NEVER drag the speaker to move it, as this will damage the spikes,

the feet and/or the wood cabinet itself. Always lift the speaker and

carry it to its new location.

CAUTION: Floorstanding (tower) loudspeakers have a high center of

gravity and may become unstable and tip over during earthquakes

or, if rocked, tipped or improperly positioned. If this is a concern,

these speakers should be anchored to the wall behind them, using

the same procedures and hardware customary for anchoring

bookcases and wall units. The customer is responsible for proper

installation and proper selection of hardware.

SPEAKER SETUP

SPEAKER PLACEMENT

Proper placement of the speakers is an important step in obtaining

the most realistic soundstage possible. These recommendations

are for the optimum placement of the loudspeakers. Use these

placement recommendations as a guide. Slight variations will not

diminish your listening pleasure. The TL260 loudspeaker is video-

shielded and may safely be placed near a television.

MODEL: TL260

WIRING THE SYSTEM

IMPORTANT: Make sure all equipment is turned off

before making any connections.

For speaker connections, use a high-quality speaker wire with

polarity coding. The side of the wire with a ridge or other coding

is usually considered positive polarity (i.e., +).

NOTE: If desired, consult your local JBL dealer about speaker wire

and connection options.

The speakers have coded terminals that accept a variety of wire

connectors. The most common connection is shown in Figure 1.

To ensure proper polarity, connect each + terminal on the back of

the amplifier or receiver to the respective + (red) terminal on each

speaker, as shown in Figure 3. Connect the – (black) terminals in a

similar way. See the owner’s guides that were included with your

amplifier, receiver and television to confirm connection procedures.

IMPORTANT: Do not reverse polarities (i.e., + to –

or – to +) when making connections. Doing so will

cause poor imaging and diminished bass response.

Figure 1. This figure shows how to connect bare wires to the

terminals.

Figure 2. This example shows how to connect bare wires to the

terminals.

Figure 3. Wiring diagram shows polarity connections for one channel

of a stereo or home theater system.

26766_TL260 OM_ENG 18/04/06 12:51 Side 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL TL260 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info