Bedienungsanleitung Jeep Cherokee - 2016 (Seite 30 von 236) (Englisch)

617804

Zoom out

Zoom in

Vorherige Seite

1/236

Nächste Seite

Installing The Child Restraint Using The Vehicle Seat Belts

The seat belts in the passenger seating positions are equipped with a Switchable

Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the

seat belt tight around the child restraint. Any seat belt system will loosen with time,

so check the belt occasionally, and pull it tight if necessary.

Tether Anchorage Weight Limit

Always use the tether anchor when using the seat belt to install a forward facing child

restraint, up to the recommended weight limit of the child restraint.

To Install A Child Seat Using An ALR:

1. Pull enough of the seat belt webbing from the retractor to pass it through the belt

path of the child restraint. Do not twist the belt webbing in the belt path.

2. Slide the latch plate into the buckle until you hear a “click.”

3. Pull on the webbing to make the lap portion tight against the child seat.

4. To lock the seat belt, pull down on the shoulder part of the belt until you have

pulled all the seat belt webbing out of the retractor. Then, allow the webbing to

retract back into the retractor. As the webbing retracts, you will hear a clicking

sound. This means the seat belt is now in the Automatic Locking mode.

5. Try to pull the webbing out of the retractor. If it is locked, you should not be able

to pull out any webbing. If the retractor is not locked, repeat the last step.

Finally, pull up on any extra webbing to tighten the lap portion around the child

restraint while you push the child restraint rearward and downward into the vehicle

seat.

7. If the child restraint has a top tether strap and the seating position has a top tether

anchorage, connect the tether strap to the anchorage and tighten the tether strap.

See below for directions to attach a tether anchor.

Test that the child restraint is installed tightly by pulling back and forth on the child

seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction.

Installing The Top Tether Strap (With Either Lower Anchors Or Vehicle Seat Belt):

When installing a forward-facing child restraint, always secure the top tether strap,

up to the tether anchor weight limit, whether the child restraint is installed with the

lower anchors or the vehicle seat belt.

Tether Strap Installation

1. Route the tether strap to provide the most direct path for the strap between the

anchor and the child seat.

2. If your vehicle is equipped with adjustable rear head restraints, raise the head

restraint, and where possible, route the tether strap under the head restraint and

between the two posts. If not possible, lower the head restraint and pass the

tether strap around the outboard side of the head restraint.

GETTING STARTED

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jeep Cherokee - 2016 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jeep Cherokee - 2016

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info