Bedienungsanleitung Jensen MP5620SE (Seite 5 von 26) (Englisch)

509260

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

MP5620 / MP5620SE

Installation

This unit is designed for installation in cars, trucks and vans with an existing radio opening. In

many cases, a special installation kit will be required to mount the radio to the dashboard.

These kits are available at electronics supply stores and car stereo specialist shops. Always

check the kit application before purchasing to make sure the kit works with your vehicle. If you

have trouble locating a kit or need installation assistance, contact Technical Support at 1-800-

323-4815 from 8:30am to 7:00pm EST Monday through Friday and from 9:00am to 5:00pm

EST on Saturday.

Universal Installation Using Mounting Sleeve

1. Remove the detachable front panel if it is attached to the chassis by pushing the

“Release” button.

2. Slide the mounting sleeve off of the chassis if not already removed. If it is locked into

position, use the removal tools (supplied) to disengage it.

3. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is

not large enough, carefully cut or file as necessary until the sleeve easily slides into the

opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that

there will be sufficient space behind the dashboard for the radio chassis.

4. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.

With the sleeve fully inserted into the dashboard opening, bend as many of the tabs

outward as necessary so that the sleeve is firmly secured to the dashboard.

5. Place the radio in front of the dashboard opening so that the wiring can be brought

through the mounting sleeve.

6. Follow the wiring diagram carefully and make certain all connections of the wiring

harness are secure and insulated with crimp connectors or electrical tape to ensure

proper operation of the unit.

7. After completing the wiring connections, attach the front panel and turn the unit on to

confirm operation (ignition switch must be on). If unit does not operate, recheck all wiring

until problem is corrected. Once proper operation is achieved, turn off the ignition switch

and proceed with final mounting of the chassis.

8. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is

fully seated and the spring clips lock it into place.

9. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of

the chassis using the hex nut provided. Fasten the other end of the perforated strap to a

secure part of the dashboard either above or below the radio using the screw and hex nut

provided. Bend the strap to position it as necessary. CAUTION: The rear of the radio

must be supported with the strap to prevent damage to the dashboard from the weight of

the radio or improper operation due to vibration.

10. Re-attach the front panel to the chassis and test radio operation by referring to the

operating instructions for the unit.

Note: For proper operation of the CD player, the chassis must be mounted within 20° of

horizontal. Make sure the unit is mounted within this limitation.

Installation

Instalación

Installation

Bend Tabs

Doble las aletas

Pliez les pattes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jensen MP5620SE Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info