MP6612i
9
Subwoofer (SUB-W)
To adjust Subwoofer options, press the MENU button (22) until “SUB-W”
appears in the display. Press the TUNE/TRACK >>| or |<< buttons (19) to
access the following settings:
• SUB-W
Turn the rotary encoder to turn the subwoofer feature ON/OFF.
• LEVEL
The sub-woofer level control is only applicable if the unit is connected to
an optional sub-woofer speaker. Turn the rotary encoder to turn the
subwoofer ON/OFF or adjust the sub-woofer level from “00” to “12”.
• Sub-woofer Low Pass Filter (LPF)
The sub-woofer LPF control is only applicable if the unit is connected to
an optional sub-woofer speaker and a subwoofer level is selected. Turn
the rotary encoder to select one of the following four Low Pass Filter
options: Flat, 80Hz, 120Hz, 160Hz. (“Flat” turns the LPF off, allowing
the sub-woofer to play full range.)
Balance (BAL/FAD)
To adjust the balance from “L10” (full left) to “R10” (full right), press the
MENU button (22) until “BAL/FAD” appears in the display. Press the TUNE/
TRACK >>| or |<< buttons (19) to adjust the balance between the left and
right speakers. “C00” represents a center balance.
Fader (BAL/FAD)
To adjust the fader from “F10” (full front) to “R10” (full rear), press the
MENU button (22) until “BAL/FAD” appears in the display. Turn the rotary
encoder to adjust the fader between the front and rear speakers. “C00”
represents a center fader level.
System Menu Operation
Press and hold the MENU button (22) for more than two seconds to access
the SYSTEM menu. Press the MENU button repeatedly or use the TUNE/
TRACK >>| or |<< buttons (19) to move through the following menu options:
Time Format, VOL SEL, BEEP, Area, LOCAL, Bright, LCD Mode, Screen
Save. The following procedures assume you have already accessed the
menu.
Time Format
This option allows selection of a 12 hour or 24 hour clock format. “12
HOUR” is the default setting. Turn the rotary encoder to change to the 24
hour clock format.
Programmable Turn-on Volume Level (VOL SEL)
Press the MENU button (22) to select “Last” or “Adjust”.
• Last
When the unit is turned on, the volume will resume at the level selected
when last turned off.
• Adjust
After selecting “Adjust”, press the MENU button to select “Volume
PGM” and then turn the rotary encoder (22) to select the desired turn-
on level (0-46). When this option is selected, the unit will revert to the
adjusted volume each time the unit is turned on.
BEEP
Turn the rotary encoder to select “ON” or “OFF”. When “ON” is selected, an
audible beep tone is heard each time a button is pressed on the face of the
radio. “BEEP ON” is the default setting.
Frequency Spacing (Area)
This option allows you to select the appropriate frequency spacing for your
area. “U.S.A.” is the default setting. Turn the rotary encoder to select
“EUROPE”, if needed.
LOCAL
Turn the rotary encoder to turn local radio reception “ON” or “OFF”. When
the Local function is on, only radio stations with a strong signal are played.
Bright
This option allows you to adjust the brightness of the LCD screen. Turn the
rotary encoder to select a brightness level between “01” and “08”, with “08”
being the brightest.
LCD Mode
Turn the rotary encoder to select “Normal” or “Reverse”, depending on
personal preference. “Reverse” will reverse the black and white pixel
display.
Screen Save
Turn the rotary encoder to select “ON” or “OFF”. When “ON” is selected, the
screensaver will appear after 5 seconds of inactivity, allowing your music to
continue playing.
Clock Set
1. Press and hold the DISP button (18) until the clock blinks.
2. Turn the rotary encoder (22) to the right the set the hour and to the left
to set the minutes.
