Bedienungsanleitung JGC URCD-20 (Seite 30 von 39) (Deutsch, Englisch)

623895

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

ENGLISH

CLOCK FUNCTIONS

Operating the radio

• Slide the FUNCTION switch (22) on the device to AM or FM. If the function switch is in the AM position, the

device is operating in the AM radio range. If the function switch is in the FM position, the device is operating

in the FM radio range.

• Select the desired radio station by means of the TUNING control (27).

• The LED indicator FMST. (C) will come on, if you are receiving a FM stereo station. Only FM stations are

broadcast in stereo.

Setting the time

• After you have connected the power plug (25) to a power outlet, the time 12:00 will blink in the display(7).

• Hold the CLOCK/ADJ. button (18) down for 2 seconds. Either 24 H or 12 H will be shown in the display. To

change the time conﬁguration, hold the CLOCK/ADJ. button (18) down again for 2 seconds. If you choose

the 24-hour time format, the time of 0.00 will blink in the display panel. For the 12-hour time format, the

time 12:00 will blink in the display.

• Press the /MINUTE button (12) to set the minutes and the /HOUR button (11) to set the hours.

Conﬁrm by pressing the CLOCK/ADJ. button.

• If you select the 12-hour display, the LED indicator PM (D) will also be displayed for times after noon.

• If you would like to reset the time again later, press brieﬂy on the CLOCK/ADJ. button. The time will blink in

the display. Set the time by means of the /MINUTE and /HOUR buttons and conﬁrm by pressing the

CLOCK/ADJ. button.

The time will not be saved, if you pull the plug (25) and if there are no batteries in the battery

compartment (24) on the back of the device. In that event, set the new time again.

Setting the alarm

• You can set a time to wake up at which the device will come on either in the radio or CD mode. Or you can

be awakened by an alarm signal. You can save two wake-up times in total.

• Press the ALARM1 (15) or the ALARM2 (14) button. The time digits will blink in the display.

• Set the wake up time with the /MINUTE (12) and /HOUR (11) buttons and conﬁrm it by pressing

either the ALARM1 or ALARM2 button.

• The LED indicator AL.1 (J) or AL.2 (I) will light up. If you have saved 2 wake up times, both LED indicators

will come on.

• Set the desired volume by turning the volume control (23) on the device.

• Set the FUNCTION switch (22) to CD, if you would like to be awakened by music from a CD. Make sure that

there is a CD in the CD compartment (1).

• Set the FUNCTION switch to AM or FM, if you would like to be awakened by the radio. Select the desired

radio station by means of the TUNING control (27).

• Set the FUNCTION switch to BUZZER/AUX IN in order to be awakened by an alarm signal.

JGC-URCD-20-IM-DE-EN-V1.indb 30 29/01/2010 5:26 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JGC URCD-20 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info