Bedienungsanleitung JL Audio 1 (Seite 10 von 13) (Englisch)

700439

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

18 | JL Audio - HD1200/1 Owner’s Manual

The Nine-Step Procedure

1) Disconnect the Speaker Connector Plug.

2) Turn off all processing on the source unit

(bass/treble, loudness, EQ, etc.). Set fader

control to center position and subwoofer

level control to 3/4 of maximum (if used

to drive the HD1200/1). Disconnect

the HD-RLC Remote Level Control

temporarily (if one is being used).

3) Switch the “Input Voltage” to “Low” and turn

the “Input Sens.” control all the way down.

4) Set the source unit volume to 3/4 of full

volume. If the amplifier is being driven by a

source unit’s dedicated subwoofer output, also

adjust the source unit’s subwoofer level control

to 3/4 of maximum output. This will allow for

reasonable gain overlap with moderate clipping

at full volume.

5) Using the chart below, determine the

target voltage for input sensitivity

adjustment according to the nominal

impedance of the speaker system

connected to each set of outputs.

Nom.

Impedance

HD 1200/1

MONO

8 69.3 V

6 69.3 V

4 69.3 V

3 60.0 V

2 49.0 V

1.5 42.4 V

6) Verify that you have disconnected the Speaker

Connector Plug before proceeding. Play a

track with an appropriate sine wave (within

the frequency range to be amplified by each

set of channels) at 3/4 source unit volume.

7) Connect the AC voltmeter to the Speaker

Output contacts of the amplifier.

8) Increase the “Input Sens.” control until the

target voltage is delivered. If excessive voltage

is read with the control at minimum (full

counterclockwise), switch the “Input Voltage”

switch to “High” and re-adjust.

9) Once you have adjusted the amplifier to its

maximum unclipped output level, reconnect

the speaker(s). The “Input Sens.” controls can

now be adjusted downward if the HD1200/1

requires attenuation to achieve the desired

system balance.

APPENDIX B:

Precise Frequency Selection Chart

“FILTER FREQ”

Detent Panel Actual

Number Marking Freq.

Full counter-clockwise: 53

01 ...........“50” ............53

02 ............................53

03 ............................53

04 ............................53

05 ............................54

06 ............................56

07 ............................58

08 ...........“60” ............60

09 ............................62

10 ............................64

11 ............................66

12 ............................68

13 ............................71

14 ............................74

15 ............................76

16 ...........“80” ............80

17 ............................83

18 ............................87

19 ............................91

20 .............. ..............94

21 ............................99

22 ...........................104

23 ...........................109

24 .......“12 o’clock” .......115

25 ...........................121

26 ...........................128

27 ...........................137

28 ...........................147

29 ...........................160

30 ...........................174

31 ...........................191

32 ...........................211

33 ..........“250” ..........236

34 ...........................269

35 ...........................309

36 ...........................369

37 ...........................443

38 ..........“500” ..........484

39 ...........................525

Full-clockwise: 528

APPENDIX C:

Input Sensitivity Level Setting

JL Audio amplifiers utilizing the Regulated

Intelligent Power Supply (R.I.P.S.) allow

delivery of their rated power when connected

to any load impedance from 1.5 - 4Ω per

channel and when connected to a charging

system with any voltage from 11 - 14.5V.

This design is beneficial for many reasons.

One of these reasons is ease of setup.

Because each JL Audio amplifier will

always deliver the same amount of power

within its operational range of impedances

and supply voltages, the maximum,

unclipped output is very predictable.

This makes setting the gain structure via the

input sensitivity controls very simple. Following

the directions below will allow the user to adjust

the input sensitivity of the amplifier(s) simply

and easily in just a few minutes using equipment

which is commonly available in installation bays.

Necessary Equipment

• Digital AC Voltmeter

• CD with a sine-wave test tone recorded at

0 dB reference level in the frequency range

to be amplified for that set of channels

(50 Hz for subwoofer channels, 1 kHz for

a midrange application). The CleanSweep®

Calibration Disc contains the appropriate

test tones and is available for sale at

http://store.jlaudio.com Do not use attenuated

test tones (-10 dB, -20 dB, etc.).

Do not increase any “Input Sens.” setting in

the system beyond the maximum level

established during this procedure. Doing so

will result in audible distortion and possible

speaker damage.

It will be necessary to re-adjust the “Input

Sens.” for the affected channels if any equalizer

boost is activated after setting the “Input

Sens.” with this procedure. This applies to any

EQ boost circuit, source unit tone controls or EQ

circuits. EQ cuts will not require re-adjustment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio 1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info