Bedienungsanleitung JL Audio 10W7 (Seite 8 von 16) (Englisch)

701353

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

12W7-3

Free Air Resonance (Fs): 27.2 Hz

Electrical “Q” (Qes): 0.514

Mechanical “Q” (Qms): 7.807

Total Speaker “Q” (Qts): 0.482

Equivalent Compliance (Vas): 2.33 cu. ft. (66.0 ltrs)

One-Way, Linear Excursion (Xmax)*: 1.15 in. (29 mm)

Thermal Power Handling (Pt): 1000 Watts Continuous

Reference Efficiency (no): 0.249 %

Efficiency (SPL @ 1W/1m): 86.2 dB

DC Resistance (Re): 2.47Ω

Effective Piston Area (Sd): 84 sq. in. (0.0542 sq. m)

Nominal Impedance (Znom): 3Ω

* Xmax specifications are derived via one-way voice coil overhang method with

no correction factors applied.

Infrasonic Filter:

Turn “O” for Sealed Enclosure.

Turn “On” for Ported Enclosure and

set the knob to “25” Hz.

Bass EQ:

Generally not necessary in W7 applications (we recommend defeating it by

switching the “Bass EQ” switch to “O”). May be used with Remote Bass

Control to provide some user controllable broad bass boost. When used in this

manner, set “Q” to “1.1”, set “Center Freq.” to “45” Hz, “Boost” is defeated by

connection of Remote Bass Control.

Input Sensitivity Controls:

Proper adjustment of these controls is critical!

For virtually all aftermarket head units,

set “Input Voltage” to “Low”.

See “Input Sensitivity Setting Guide”

on pg. 14 for precise setting instructions.

Dual Mono Speaker

Output Connections:

Connect wire directly to “+”

and “–” “Subwoofer Output”

connections and to the W7.

Remote Bass Port:

Permits connection of an

optional remote bass boost

controller (RBC-1), giving you

control over the boost of the

parametric EQ from the front

of the vehicle. The RBC-1

controller is sold separately.

Amp Low-Pass Filter:

Set “Mode/Slope” switch to “24dB”.

Set “Filter Freq. (Hz)” knob to “85”.

Lower settings are likely to result in a

poor transition between the upper

response of the W7 and the lower

response of the mid-bass speakers.

Amplier Input:

Connect RCA-type

cables from the head

unit (or processor) to

these two jacks.

Use both jacks

(with a Y-adapter

if necessary).

Output Polarity:

Carefully listen to the sub-bass to

mid-bass transition with music that

has strong mid-bass content. Select

the switch position which gives the

smoothest, most natural mid-bass

response. If using multiple 1000/1’s

on multiple subwoofers, make sure

this switch is set to the same position

on all ampliers.

JL Audio 1000/1v2:

These settings are intended

as a “baseline” for tuning your

system. Depending on your

vehicle and your preferences,

some variation in the crossover

and bass control settings may

be necessary for optimum

performance. (See settings

on page 10 for 500/1.)

RECOMMENDED CONTINUOUS RMS POWER RANGE FOR ONE SUBWOOFER DRIVER:

500W 750W 1000W 2000W 4000W250W

= position of knob

= position of switch

= switch with two possible positions

= setting will vary (see sidebar)

Amplifier Recommendation: 1000/1v2 (pictured), HD750/1,

500/1v2 or G-MAX

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio 10W7 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info