Bedienungsanleitung JL Audio 13W7 (Seite 6 von 16) (Englisch)

701355

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Infrasonic Filter:

Turn “O” for Sealed Enclosure.

Turn “On” for Ported Enclosure and

set the knob to “25” Hz.

Bass EQ:

Generally not necessary in W7 applications (we recommend defeating it by

switching the “Bass EQ” switch to “O”). May be used with Remote Bass

Control to provide some user controllable broad bass boost. When used in this

manner, set “Q” to “1.1”, set “Center Freq.” to “45” Hz, “Boost” is defeated by

connection of Remote Bass Control.

Input Sensitivity Controls:

Proper adjustment of these controls is critical!

For virtually all aftermarket head units,

set “Input Voltage” to “Low”.

See “Input Sensitivity Setting Guide”

on pg. 14 for precise setting instructions.

Dual Mono Speaker

Output Connections:

Connect wire directly to “+”

and “–” “Subwoofer Output”

connections and to the W7.

Remote Bass Port:

Permits connection of an

optional remote bass boost

controller (RBC-1), giving you

control over the boost of the

parametric EQ from the front

of the vehicle. The RBC-1

controller is sold separately.

Amp Low-Pass Filter:

Set “Mode/Slope” switch to “24dB”.

Set “Filter Freq. (Hz)” knob to “85”.

Lower settings are likely to result in a

poor transition between the upper

response of the W7 and the lower

response of the mid-bass speakers.

Amplier Input:

Connect RCA-type

cables from the head

unit (or processor) to

these two jacks.

Use both jacks

(with a Y-adapter

if necessary).

Output Polarity:

Carefully listen to the sub-bass to

mid-bass transition with music that

has strong mid-bass content. Select

the switch position which gives the

smoothest, most natural mid-bass

response. If using multiple 1000/1’s

on multiple subwoofers, make sure

this switch is set to the same position

on all ampliers.

JL Audio 1000/1v2:

These settings are intended

as a “baseline” for tuning

your system. Depending

on your vehicle and your

preferences, some variation in

the crossover and bass control

settings may be necessary

for optimum performance.

RECOMMENDED CONTINUOUS RMS POWER RANGE FOR ONE SUBWOOFER DRIVER:

750W 1000W 1500W 2000W 4000W500W

= position of knob

= position of switch

= switch with two possible positions

= setting will vary (see sidebar)

Amplifier Recommendation: 1000/1v2

13W7-D1.5

Free Air Resonance (Fs): 23.5 Hz

Electrical “Q” (Qes): 0.476

Mechanical “Q” (Qms): 7.517

Total Speaker “Q” (Qts): 0.448

Equivalent Compliance (Vas): 3.68 cu. ft. (104.3 ltrs)

One-Way, Linear Excursion (Xmax)*: 1.25 in. (32 mm)

Thermal Power Handling (Pt): 1500 Watts Continuous

Reference Efficiency (no): 0.269 %

Efficiency (SPL @ 1W/1m): 86.3 dB

DC Resistance (Re): 2.41Ω

Effective Piston Area (Sd): 107.35 sq. in. (0.0693 sq. m)

Nominal Impedance (Znom): Dual 1.5Ω

* Xmax specifications are derived via one-way voice coil overhang

method with no correction factors applied.

** For parallel-wired voice coils, divide “Re” by 4.

All other specifications remain the same.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio 13W7 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info